Andersen Tribeca Sliding Door Exterior Key Lock Assembly (Left Hand), White

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Andersen Tribeca style exterior key lock assembly. This left-hand (LH) lock, in white, is designed to enhance the security and convenience of your Andersen gliding patio door by allowing external key access. It is compatible with Andersen 200-series Narroline, 200-series Perma-Shield, and 400-series Frenchwood gliding patio doors manufactured from 1982 to the present.

Коопсуздук маалыматы

• Always wear appropriate safety gear, such as safety glasses, when drilling or using tools.
• Жумуш аймагы жакшы жарыктандырылсын жана тоскоолдуктардан таза болсун.
• Майда тетиктерди жана шаймандарды балдар жетпеген жерде сактаңыз.
• Эгер кандайдыр бир кадамга ишенбесеңиз, квалификациялуу адиске кайрылыңыз.

Пакеттин мазмуну

Орнотууну баштоодон мурун бардык компоненттер бар экендигин текшериңиз:

• Exterior Key Lock Assembly (Left Hand)
• Баскычтар (2)
• Монтаждоо бурамалар

Орнотуу жана орнотуу

Керектүү куралдар

• Бургулоо
• Drill bits (appropriate sizes for pilot holes and lock cylinder)
• Бурагыч (Phillips баш)
• Өлчөөчү лента же сызгыч
• Карандаш
• Wood clamp and scrap wood (recommended to prevent paint chipping)

Орнотуу кадамдары

This lock assembly is designed to be installed on the left side operating panel when viewed from the outside of the house.

1. эшикти даярдоо: Carefully examine the existing door panel where the lock will be installed. Ensure the area is clean and free of debris.
2. Бургулоо жерлерин белгилөө: Using the lock assembly as a template, accurately mark the locations for drilling pilot holes and the main cylinder hole on the exterior of the door panel. Double-check measurements to ensure proper alignment with the interior latch mechanism.
3. Бургулоо тешиктери: Before drilling, it is highly recommended to clamp a piece of scrap wood to the outside of the door panel at the drilling location. This helps prevent the paint from chipping as the drill bit exits the material. Drill pilot holes and the larger hole for the lock cylinder as marked.
4. Кулпу цилиндрин орнотуу: Insert the exterior key lock cylinder into the prepared hole. Ensure it seats properly. Маанилүү: Avoid turning the cylinder prior to installation, as this may cause the unit to malfunction.
5. Ассамблеяны камсыз кылуу: Align the exterior lock assembly with the drilled holes and the interior latch mechanism. Secure the assembly using the provided mounting screws. Do not overtighten.
6. Сыноо операциясы: Insert a key and test the locking and unlocking mechanism from the outside. Verify that the lock engages and disengages smoothly.
7. Check Interior Latch Compatibility: For older sliding doors, ensure the existing interior thumb latch is long enough to properly engage with the new exterior key lock. If the interior latch is not 1 3/8 inches, a compatible Tribeca interior latch may be required for optimal function.

Image: Andersen Tribeca Exterior Key Lock Assembly in white. This image shows the complete lock assembly, including the key cylinder and mounting plate, ready for installation on a sliding patio door.

Иштөө нускамалары

To operate the Andersen Tribeca exterior key lock assembly:

• Бекитүү: Insert the key into the keyhole on the exterior lock. Turn the key clockwise until the lock mechanism engages and the door is secured. Remove the key.
• Кулпуну ачуу үчүн: Insert the key into the keyhole. Turn the key counter-clockwise until the lock mechanism disengages. The key may need to be turned a full rotation to be removed.
• The door can still be locked and unlocked from the interior using the existing thumb latch.

Техникалык тейлөө

To ensure the longevity and smooth operation of your lock assembly:

• Тазалоо: Clean the exterior surface of the lock with a soft, damp кездеме. Финишке зыян келтирүүчү абразивдүү тазалагычтардан же эриткичтерден качыңыз.
• Майлоо: Periodically apply a small amount of graphite lubricant or a silicone-based spray specifically designed for locks into the keyhole to maintain smooth key operation.
• Аба ырайын жабуу: If your door is exposed to the elements, consider applying a small amount of silicone sealant around the edges of the lock plate after installation to prevent moisture intrusion.

Проблемаларды чечүү

• Lock Not Engaging/Disengaging Smoothly:
  - Check for obstructions in the door track or frame.
  - Ensure the mounting screws are not overtightened, which can cause binding.
  - Verify that the interior thumb latch is correctly aligned and engaging with the exterior lock mechanism. An older or incompatible interior latch (not 1 3/8 inches) may need replacement.
• Ачкычты киргизүү же буруу кыйын:
  - Apply a graphite or silicone-based lock lubricant into the keyhole.
  - Ensure the key is fully inserted before turning.
  - Check if the lock cylinder was turned prior to installation; this can cause misalignment.
• Paint Chipping During Drilling:
  - This can occur if a scrap wood block was not clamped to the exterior of the door during drilling. While not repairable by this manual, future installations should follow this recommendation.

Техникалык шарттар

Кепилдик маалымат

This product is covered by Andersen's standard limited warranty. For specific details regarding warranty coverage, duration, and terms, please refer to the warranty information included with your product packaging or visit the official Andersen webсайт. Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.

Колдоо жана Байланыш

If you have any questions, require technical assistance, or need to order replacement parts, please contact Andersen customer support directly. Refer to the contact information provided on the product packaging or visit the official Andersen webэң акыркы колдоо параметрлери үчүн сайт.