MAC Auto Parts Brake Service Kit User Manual

Introduction

This manual provides essential information for the installation, operation, and maintenance of your MAC Auto Parts 6-Piece OE Replacement Brake Service Kit. This kit is designed to replace the front and rear brake disc rotors and ceramic brake pads on compatible vehicles, ensuring optimal braking performance and safety. Please read this manual thoroughly before proceeding with installation or maintenance.

Продукт бүттүview жана компоненттер

The MAC Auto Parts 6-Piece OE Replacement Brake Service Kit includes all necessary components for a complete front and rear brake service. The kit is comprised of high-quality brake disc rotors and ceramic brake pads, engineered for durability and performance.

Figure 1: Complete 6-Piece Brake Service Kit including front and rear rotors and ceramic pads.

Комплекттин мазмуну:

• 2x Front Brake Disc Rotors: Part# R1184 1407-479087 BR901184 121.51052
• 1x Front Brake Disc Pads Ceramic: Part# SCD1432 (4 Pads = 1 Set)
• 2x Rear Brake Disc Rotors: Part# 10-31553 REF# BR900894 121.51039
• 1x Rear Brake Disc Pads Ceramic: Part# SCD1284 (4 Pads = 1 Set)

Унаа шайкештиги

This brake service kit is compatible with the following vehicle makes and models:

• 2013-2016 Hyundai Santa Fe: Бардык моделдер
• 2014-2016 Kia Sorento: Бардык моделдер

Important: Always confirm vehicle compatibility before installation to ensure proper fitment and safe operation.

Орнотуу жана орнотуу

Installation of brake components requires specialized tools and knowledge. It is highly recommended that installation be performed by a qualified automotive technician. Improper installation can lead to brake system failure, resulting in serious injury or death.

Коопсуздук чаралары:

• Ар дайым тиешелүү жеке коргонуу шаймандарын (ЖКК), анын ичинде коргоочу көз айнектерди жана кол каптарды кийиңиз.
• Ensure the vehicle is securely supported on jack stands on a level surface before beginning work.
• Disconnect the vehicle's battery before working on any electrical components.
• Do not work under a vehicle supported only by a jack.
• Refer to your vehicle's specific service manual for detailed brake system removal and installation procedures.

Орнотуунун жалпы кадамдары (өзгөчө маалымат алуу үчүн Унаа колдонмосун караңыз):

1. Safely lift and support the vehicle. Remove the wheels.
2. Remove the brake caliper and support it without straining the brake hose.
3. Remove the old brake pads and brake disc rotor.
4. Clean the hub surface thoroughly to ensure proper seating of the new rotor.
5. Install the new MAC Auto Parts brake disc rotor.
6. Install the new MAC Auto Parts ceramic brake pads into the caliper bracket.
7. Reinstall the brake caliper and secure all fasteners to the manufacturer's torque specifications.
8. Repeat for all wheels.
9. Bleed the brake system if brake lines were opened or if air is suspected in the system.
10. Pump the brake pedal several times to seat the pads against the rotors before driving.
11. Perform a test drive in a safe area at low speed to confirm proper brake function.

Иштетүү жөнүндө ойлор

After installation, it is crucial to properly "bed-in" the new brake pads and rotors. This process helps to transfer a thin, even layer of pad material onto the rotor surface, which is essential for optimal braking performance and longevity, and to prevent noise and vibration.

Brake Bed-In Procedure:

1. Жол кыймылы аз болгон коопсуз, ачык аймакты табыңыз.
2. Болжол менен саатына 55 км (35 миль) ылдамдыкка чейин ылдамдаңыз жана саатына 8 км (5 миль) чейин жайлатуу үчүн орточо тормоздук басымды колдонуңуз. Толук токтобоңуз.
3. Repeat this process 5-6 times, allowing a few minutes between each cycle for the brakes to cool slightly.
4. After the initial cycles, accelerate to approximately 50 mph (80 km/h) and apply firm braking pressure (but not hard enough to activate ABS) to slow down to about 5 mph (8 km/h).
5. Repeat this firmer braking process 2-3 times, again allowing for cooling between cycles.
6. Avoid heavy braking or prolonged stops immediately after the bed-in procedure. Allow the brakes to cool completely before normal driving.

During the bed-in process, you may notice some smoke or a burning smell; this is normal. After bed-in, the brakes should provide consistent and quiet performance.

Техникалык тейлөө

Regular inspection and maintenance of your brake system are vital for safety and performance. Follow your vehicle manufacturer's recommended maintenance schedule.

Сунушталган тейлөө практикалары:

• Үзгүлтүксүз текшерүү: Inspect brake pads, rotors, calipers, and brake lines at least once a year or every 12,000 miles (20,000 km), or as recommended by your vehicle manufacturer.
• Төшөк кийими: Replace brake pads when they reach their minimum thickness specification (typically 2-3mm).
• Ротордун абалы: Check rotors for excessive wear, scoring, cracks, or warping. Rotors should be replaced if they fall below minimum thickness or show significant damage.
• Тормоз суюктугу: Тормоз суюктугунун деңгээлин жана абалын дайыма текшерип туруңуз. Унааңыздын өндүрүүчүсүнүн сунуштарына ылайык тормоз суюктугун алмаштырыңыз.
• Тазалык: Keep brake components free from dirt, debris, and corrosion.

Проблемаларды чечүү

If you experience any issues with your brake system after installing this kit, consult the following common troubleshooting tips. For complex issues, always seek assistance from a qualified technician.

Common Brake Issues:

• Тормоздун ызы-чуусу (Чыйкыруу/Жармалоо):
  • Чыйылдап: Often caused by new pads not being properly bedded-in, or lack of anti-squeal shims/lube. Ensure proper bed-in and correct installation of all components.
  • Майдалоо: Typically indicates severe pad wear, where the metal backing plate is contacting the rotor. Inspect pads immediately and replace if worn.
• Vibration/Pulsation during Braking:
  • Often caused by warped rotors or uneven pad material transfer. Ensure proper bed-in procedure was followed. Inspect rotors for runout.
• Төмөндөтүлгөн тормоздук көрсөткүч:
  • Could be due to air in the brake lines (if lines were opened), contaminated pads, or improper bed-in. Check for leaks, re-bleed brakes, or re-perform bed-in.
• Pulling to One Side during Braking:
  • May indicate a seized caliper, uneven pad wear, or a brake hose issue on one side. Inspect calipers and hoses.

Warning: Any significant brake system issue should be addressed immediately by a professional to ensure vehicle safety.

Техникалык шарттар

Кепилдик маалымат

The warranty for your MAC Auto Parts brake service kit is stated on the product listing at the time of purchase. For specific details regarding warranty coverage, duration, and terms, please refer to the original product listing or contact the seller directly.

Figure 2: Warranty statement from the product listing.

If you have any questions regarding the warranty or require assistance, please contact the seller or manufacturer through the contact information provided on your purchase receipt or the product's sales platform.

Колдоо

For technical assistance, installation guidance, or any other product-related inquiries, it is recommended to consult a certified automotive professional. You may also reach out to the seller or manufacturer for support, referencing your purchase details and the product model number.

Өндүрүүчү: Mac автоунаа тетиктери

For further assistance, please refer to the contact information provided with your purchase or on the official MAC Auto Parts webсайт (эгер бар болсо).