HPE 500W Flex Slot Platinum Hot-Plug Power Supply User Manual

1. Киришүү

This manual provides essential information for the safe and efficient use of the HPE 500W Flex Slot Platinum Hot-Plug Power Supply, model 865408-B21. This power supply unit (PSU) is designed to deliver reliable and highly efficient power to compatible HPE server systems, supporting hot-plug and redundant configurations for enhanced system uptime.

Негизги өзгөчөлүктөр төмөнкүлөрдү камтыйт:

• 500 Watt Output: Provides stable power for server components.
• 80 PLUS Платина сертификаты: Achieves up to 96% power efficiency, reducing energy consumption and operating costs.
• Flex Slot Form Factor: Designed for compatibility with HPE servers utilizing Flex Slot power bays.
• Hot-Plug Capability: Allows for installation or replacement without powering down the server, ensuring continuous operation.
• Redundant Operation: Supports N+1 or N+N redundancy configurations for increased system reliability.

2. Коопсуздук маалыматы

Жабдуулардын бузулушун жана жаракат алуусун алдын алуу үчүн төмөнкү коопсуздук чараларын сактаңыз:

• Always disconnect the main power source from the server before performing any internal maintenance, unless specifically instructed for hot-plug procedures.
• Ensure proper grounding of the server system.
• Do not operate the power supply if it is damaged or if any cables are frayed.
• Handle the power supply by its designated handle or edges; avoid touching internal components.
• This unit contains no user-serviceable parts. Refer all servicing to qualified personnel.
• Ensure adequate ventilation around the server to prevent overheating.

3. Орнотуу жана орнотуу

Follow these steps to install the HPE 500W Flex Slot Power Supply into a compatible server.

3.1 Орнотууга чейинки текшерүүлөр

• Verify that the server chassis supports Flex Slot power supplies.
• Ensure the server's power requirements are met by the 500W output.
• Confirm that the server is powered off and disconnected from the main power source if installing the first PSU or if not performing a hot-plug replacement.

3.2 Орнотуу процедурасы

1. Locate an available Flex Slot power supply bay on your server.
2. If a blanking panel is present, remove it by pressing the release latch and pulling it out.
3. Grasp the power supply by its handle.
4. Align the power supply with the bay and slide it gently into the slot until it clicks into place. Ensure it is fully seated.
5. Connect the appropriate AC power cord to the power supply's input port and then to a grounded power outlet.

Figure 1: HPE 500W Flex Slot Power Supply, showing the fan and power input connector. The power supply features a cooling fan at one end and the AC power input connector with a red release latch at the other. A handle is integrated for easy insertion and removal.

Сүрөт 2: Жакын пландан view of the HPE 500W Flex Slot Power Supply's fan and power input, highlighting the 500W label. This image provides a detailed look at the fan grille, the '500W' rating, and the AC power connector with its red retention clip.

4. Операция

Once installed and connected, the power supply operates automatically with the server. Observe the LED indicators for status information.

4.1 Күйгүзүүнүн ырааттуулугу

Upon server power-on, the power supply will initiate its self-test. If multiple power supplies are installed, they will work in conjunction to provide power and redundancy.

4.2 Status Indicators (LEDs)

The power supply typically features an LED indicator to show its operational status:

• Катуу жашыл: Power supply is operating normally.
• Жаркылдаган жашыл: Power supply is in standby mode.
• Solid Amber/Orange: Power supply fault or failure.
• Өчүк: No power to the unit or unit failure.

Refer to your server's documentation for specific LED behavior and troubleshooting steps.

5. Техникалык тейлөө

Үзгүлтүксүз техникалык тейлөө электр менен камсыздооңуздун узак мөөнөттүү жана оптималдуу иштешин камсыз кылууга жардам берет.

5.1 Тазалоо

Periodically inspect the power supply's fan and vents for dust accumulation. Use compressed air to gently clear dust from the fan and ventilation openings. Ensure the server is powered off and disconnected from AC power before cleaning, unless performing a hot-plug cleaning procedure as per server documentation.

5.2 Fan Inspection

Listen for unusual noises from the power supply fan, which could indicate a failing fan. If a fan failure is suspected, consult the troubleshooting section or contact support.

5.3 Hot-Swap Procedure (Replacement)

If a power supply fails in a redundant configuration, it can be replaced without powering down the server:

1. Disconnect the AC power cord from the faulty power supply.
2. Press the release latch on the power supply handle and pull the unit out of the bay.
3. Insert the new power supply into the empty bay, ensuring it clicks into place.
4. Connect the AC power cord to the new power supply.
5. Verify the LED indicator on the new power supply shows solid green.

6. Кыйынчылыктарды

This section addresses common issues you might encounter with the power supply.

6.1 No Power / Power Supply LED Off

• Check AC Power: Ensure the power cord is securely connected to both the power supply and a working power outlet.
• Сыноо түйүнү: Plug another device into the outlet to confirm it has power.
• Reseat PSU: Power down the server (if not redundant), disconnect AC, remove and re-insert the power supply firmly into its bay.

6.2 Power Supply LED is Amber/Orange

• Ички ката: An amber LED typically indicates an internal fault with the power supply.
• Ашыкча жүктөө: Ensure the server's power draw does not exceed the power supply's capacity.
• Redundant Configuration: If in a redundant setup, the server should continue operating. Replace the faulty power supply as soon as possible using the hot-swap procedure.

If troubleshooting steps do not resolve the issue, proceed to the Warranty and Support section.

7. Техникалык шарттар

Technical specifications for the HPE 500W Flex Slot Platinum Hot-Plug Power Supply.

8. Кепилдик жана колдоо

For warranty information and technical support, please refer to the official HP (Hewlett Packard Enterprise) website or contact your authorized reseller. Keep your purchase receipt and product serial number readily available when seeking support.

Online resources and contact information can typically be found at www.hpe.com/support.