Einhell GE-SP 4390 N-A LL ECO Clear Water Submersible Pump

Introduction

The Einhell GE-SP 4390 N-A LL ECO submersible pump is designed for pumping clear water with high efficiency. Its advanced Aquasensor technology allows for automatic operation with extremely low suction levels, making it ideal for draining flooded basements, pools, or other areas where minimal residual water is desired. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.

Коопсуздук нускамалары

Насоско зыян келтирбөө же жаракат алуунун алдын алуу үчүн ар дайым төмөнкү коопсуздук чараларын сактаңыз:

• Ensure the power supply matches the pump's specifications (230 V).
• Эгерде электр кабели же сайгычы бузулган болсо, насосту иштетпеңиз.
• Never lift or carry the pump by its power cable. Use the integrated handle.
• The pump is designed for clear water only. Do not use it for corrosive, flammable, or explosive liquids, or for water containing large solid particles.
• Балдарды жана уруксаты жок адамдарды операциялык аймактан алыс кармаңыз.
• Disconnect the pump from the power supply before any maintenance, cleaning, or when not in use.
• Ensure the pump is placed on a stable, level surface during operation.

Продукт бүттүview

The Einhell GE-SP 4390 N-A LL ECO pump features a robust design and intelligent technology for efficient water drainage.

Сүрөт 1: Алдыңкы view of the Einhell GE-SP 4390 N-A LL ECO submersible pump.

Жайгашуу

1. Жайгашкан жери: Position the pump on a stable, level surface in the area to be drained. Ensure there is sufficient operating space around the pump (minimum 40 x 40 cm) for optimal performance and sensor function.
   

   Figure 2: Recommended minimum operating space for the pump.

2. Шланг туташтыруу: Connect a suitable discharge hose to the universal hose connection located on the top side of the pump. Ensure the connection is secure to prevent leaks.
   

   Figure 3: The easily accessible hose connection on the top of the pump.
3. Кубат туташуу: Plug the 10-meter power cable into a grounded electrical outlet (230V). Ensure the outlet is protected by a residual current device (RCD) for safety.
   

   Figure 4: The pump is equipped with a 10-meter power cable for flexible placement.

Иштөө нускамалары

The Einhell GE-SP 4390 N-A LL ECO pump features an Aquasensor for automatic operation and a manual mode.

Aquasensor Automatic Operation

The Aquasensor allows the pump to start and stop automatically based on predefined water levels. Use the selector switch on the pump to choose the desired automatic start level:

• Level 1 (1 mm start): The pump starts for 30 seconds when the water level reaches 1 mm. This is ideal for near-complete drainage.
• Level 2 (5 cm start): The pump starts when the water level reaches 5 cm and continues pumping until it reaches the 1 mm level, then runs for an additional 30 seconds.
• Level 3 (10 cm start): The pump starts when the water level reaches 10 cm and continues pumping until it reaches the 1 mm level, then runs for an additional 30 seconds.

Figure 5: The Aquasensor allows for automatic start at 5mm and stop at 1mm residual water.

Кол менен иштетүү

For continuous pumping regardless of water level, switch the pump to manual mode. In this mode, the pump will operate continuously until it is manually unplugged from the power supply. This is useful for initial rapid drainage of large volumes of water.

Figure 6: The pump effectively removes water from flooded areas, leaving minimal residue.

Кайтарылбаган клапан

The integrated non-return valve prevents water from flowing back into the drained area once the pump stops, ensuring efficient and complete drainage.

Figure 7: The non-return valve prevents backflow of water.

Техникалык тейлөө

Үзгүлтүксүз техникалык тейлөө насосуңуздун узак мөөнөттүү иштешин жана оптималдуу иштешин камсыз кылат.

• Тазалоо: After each use, especially if pumping slightly turbid water, rinse the pump with clean water. Clean the suction area and the Aquasensor to prevent blockages and ensure accurate readings.
• Текшерүү: Periodically inspect the power cable, plug, and pump housing for any signs of damage. Check the hose connection for wear.
• Сактагыч: When not in use, store the pump in a dry, frost-free location. Ensure all water is drained from the pump before storage.

Проблемаларды чечүү

Техникалык шарттар

Figure 8: The pump boasts a high flow rate of 9000 liters per hour.

Figure 9: Maximum immersion depth for the pump is 7 meters.

Figure 10: The pump can achieve a minimum suction depth of 1 mm.