Introduction
Thank you for choosing the Michelin 12294A Digital Programmable Tire Pressure Gauge. This device is designed for accurate and convenient measurement of tire pressure, ensuring optimal vehicle performance and safety. Please read this manual thoroughly before use.
Пакеттин мазмуну
- 1 x Michelin 12294A Digital Programmable Tire Pressure Gauge
- 2 x Lithium-metal batteries (pre-installed or included)
Image: The Michelin 12294A Digital Programmable Tire Pressure Gauge, showing its digital display and control buttons.
Жайгашуу
Батарея орнотуу
The device requires 2 Lithium-metal batteries. These are typically included or pre-installed. If replacement is needed:
- Locate the battery compartment cover, usually on the back or side of the unit.
- Капкакты ачыңыз.
- Туура полярдуулукту (+/-) камсыз кылуу менен батарейкаларды салыңыз.
- Батарея уясынын капкагын бекем жабыңыз.
Күйгүзүү/өчүрүү
- Күйгүзүү үчүн, басыңыз Кубат баскычы (often marked with a circle and vertical line symbol).
- The backlit LCD display will illuminate.
- Батареянын кубатын үнөмдөө үчүн түзмөк бир аз убакытка иштебей тургандан кийин автоматтык түрдө өчөт.
Иштөө нускамалары
Шинанын басымын өлчөө
- Ensure the tire is cold for the most accurate reading.
- Дөңгөлөктөн клапан капкагын алып салыңыз.
- Press the nozzle of the gauge firmly onto the tire valve stem. A good seal is crucial for an accurate reading.
- The digital display will show the tire pressure.
- Remove the gauge from the valve stem. The reading will hold on the display for a short period.
- Клапан капкагын алмаштырыңыз.
Image: The Michelin 12294A gauge being used to measure pressure on a car tire valve.
Өлчөө бирдиктерин өзгөртүү
The gauge supports measurements in PSI, KPA, BAR, and kg/cm². To cycle through units, press the Бирдик баскычы (often the same as the power button or a dedicated button). The current unit will be displayed on the screen.
Programming Tire Pressures
This gauge can be programmed with target front and rear tire pressures for up to two vehicles. Refer to your vehicle's owner's manual or the sticker on the driver's side door jamb for recommended tire pressures.
- With the gauge powered on, press and hold the Программа баскычы (often an arrow button or a dedicated 'SET' button) until the programming mode is activated.
- колдонуу Өйдө/төмөн жебе баскычтары to adjust the target pressure for the front tires of Vehicle 1.
- басыңыз Программа баскычы again to switch to the rear tires of Vehicle 1, then adjust.
- Repeat the process for Vehicle 2 if desired.
- The gauge will save the settings automatically after a few seconds of inactivity or by pressing the Program button to exit.
Сүрөт: жакын план view of the gauge's digital display, showing current pressure and programmable target pressure settings.
Using the Integrated Flashlight
The gauge features an integrated flashlight to assist in locating the tire valve in low-light conditions. To activate the flashlight, press the Фонар баскычы (refer to device markings, often combined with another function or a dedicated button).
Using the Bleed Valve
If a tire is over-inflated, the built-in bleed valve allows for controlled release of air. While the gauge is attached to the valve stem and displaying pressure, gently press the Bleed Valve button (if present, often a small button near the nozzle) to release air until the desired pressure is reached.
Техникалык тейлөө
- Тазалоо: Wipe the gauge with a soft, dry cloth. Do not use abrasive cleaners or immerse the device in water.
- Сактагыч: Store the gauge in a cool, dry place, away from direct sunlight and extreme temperatures.
- Батареяны алмаштыруу: If the display becomes dim or the device does not power on, replace the batteries. Dispose of old batteries according to local regulations.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| No display/Device does not power on | Өлүк же туура эмес орнотулган батарейкалар. | Батареянын полярдуулугун текшериңиз же батарейкаларды алмаштырыңыз. |
| Туура эмес окуу | Poor seal with valve stem; tire not cold; gauge malfunction. | Ensure a firm, airtight seal. Measure when tires are cold. If issues persist, contact support. |
| Air leaks when measuring | Gauge not properly seated on valve stem. | Press the gauge firmly and squarely onto the valve stem. |
Техникалык шарттар
| Бренд | МИШЕЛИН |
| Модель номери | 12294A |
| Модель аты | Басым өлчөгүч |
| Продукт Салмагы | 100 г |
| Продукциянын өлчөмдөрү | 9.3 x 3.3 x 2 см |
| Батареялар | 2 Литий-металл (кошулган) |
| Өлчөө бирдиктери | PSI, KPA, BAR, кг/см² |
| Тактык | +/- 1% |
| Материал | Metal core, ribbed plastic exterior |
| Thread Type | Schrader |
Кепилдик жана колдоо
This Michelin product is manufactured to high-quality standards. For warranty information or technical support, please refer to the documentation included with your purchase or visit the official Michelin automotive accessories webсайт. Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.
