1. Киришүү
This manual provides essential information for the safe and effective installation, operation, and maintenance of the Schneider Electric GV2ME14 Manual Motor Starter. The GV2ME14 is designed to control and protect motors against overloads, short circuits, and phase failures. Please read this manual thoroughly before proceeding with any installation or operation.
1-сүрөт: Schneider Electric GV2ME14 Manual Motor Starter in its original packaging. The packaging shows the model number GV2ME14, a current range of 6-10A, and the Schneider Electric logo. The device itself is visible next to the box.
2. Коопсуздук маалыматы
ЭСКЕРТҮҮ: Электр тогуна урунуу коркунучу. Бул жабдууну квалификациялуу адистер гана орнотушу, иштетиши же тейлеши керек. Бул көрсөтмөлөрдү аткарбоо өлүмгө же олуттуу жаракат алууга алып келиши мүмкүн.
- Always disconnect power before working on the motor starter or connected equipment.
- Бардык электр тетиктерин туура жерге туташтырууну камсыз кылыңыз.
- Тиешелүү жеке коргонуу шаймандарын (ЖКК) колдонуңуз.
- Verify all wiring connections are secure and conform to local and national electrical codes.
- Эгер аппарат бузулуп калса, аны иштетпеңиз.
3. Орнотуу жана орнотуу
3.1 Монтаждоо
The GV2ME14 motor starter can be mounted on a 35mm DIN rail or directly to a panel using screws. Ensure adequate ventilation around the device.
2-сүрөт: Side view of the GV2ME14 motor starter, illustrating the design for potential DIN rail or screw mounting. The housing features slots and indentations for secure installation.
3.2 Зымдарды туташтыруу
Connect the incoming power supply to terminals 1L1, 3L2, 5L3 and the motor leads to terminals 2T1, 4T2, 6T3. Ensure all connections are tight and secure.
3-сүрөт: Фронт view of the GV2ME14 motor starter, clearly showing the input terminals (1L1, 3L2, 5L3) at the top and output terminals (2T1, 4T2, 6T3) at the bottom. The red 'OFF' button and black 'START' button are also visible.
4-сүрөт: Төмөнкү view of the GV2ME14 motor starter, highlighting the output terminals 2T1, 4T2, and 6T3, where the motor connections are made.
- Катуу момент: 15 lb. in. (1.7 N.m) for 75°C CU AWG 8-18 conductors.
- Зым өлчөмү: Refer to the product label for specific wire gauge compatibility (e.g., 1x 1...6 mm² / AWG 18...10).
3.3 Учурдагы орнотуу
Adjust the thermal overload setting dial to match the motor's full load current (FLA). The GV2ME14 has an adjustable range of 6-10 Amperes. The tripping current is 125% of the set current.
5-сүрөт: Жакын план view of the product label on the GV2ME14 motor starter. This label provides critical technical data including voltage ratings, breaking capacities, horsepower ratings, wire sizes, tightening torque, and compliance standards (UL, CSA, CE).
4. Операция
4.1 Starting the Motor
Кара басыңыз START button to energize the motor. The button will remain depressed, indicating the motor is running.
4.2 Stopping the Motor
Кызылды басыңыз ӨЧҮРҮҮ button to de-energize the motor. The button will return to its original position.
4.3 Overload Trip
In the event of an overload or short circuit, the motor starter will automatically trip, disconnecting power to the motor. The red ӨЧҮРҮҮ button will pop out further, indicating a trip condition. To reset, wait for the device to cool down (if thermal overload), then press the red ӨЧҮРҮҮ button fully in and release it before attempting to restart.
5. Техникалык тейлөө
The Schneider Electric GV2ME14 Manual Motor Starter is designed for minimal maintenance. However, periodic checks are recommended:
- Визуалдык текшерүү: Regularly inspect the device for any signs of physical damage, discoloration, or loose connections.
- Тазалоо: Keep the device free from dust and debris. Use a dry, soft cloth for cleaning. Do not use solvents or abrasive cleaners.
- Туташуу текшерүүлөрү: Periodically verify that all terminal connections remain tight.
6. Кыйынчылыктарды
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Motor does not start when START button is pressed. | No power supply; tripped motor starter; faulty motor; incorrect wiring. | Check power supply; reset motor starter (if tripped); inspect motor and wiring. |
| Motor starter trips frequently. | Motor overload; short circuit; phase imbalance; incorrect current setting. | Verify motor load; check for short circuits; inspect motor for phase issues; ensure current setting matches motor FLA. |
| Motor runs but overheats. | Motor overload; insufficient cooling; incorrect current setting. | Reduce motor load; ensure proper motor ventilation; verify current setting. |
If troubleshooting steps do not resolve the issue, contact qualified electrical personnel or Schneider Electric support.
7. Техникалык шарттар
- Модел: GV2ME14
- Модель номери: D607807
- Бренд: Schneider Electric
- Ampэраж диапазону: 6 - 10 А
- Мотор күчү: 7-1/2 HP (at 600V)
- Материал: Copper (internal contacts)
- Продукциянын өлчөмдөрү (L x W x Y): 3.75 x 3.25 x 2 дюйм
- Элемент Салмагы: 0.01 ounces (Note: This weight may refer to packaging or a specific component; actual device weight may vary.)
- Катуу момент: 15 lb. in. (1.7 N.m)
- Стандарттар: IEC/EN 60947-2, UL Listed, CSA Certified, CE
- Breaking Capacity (Icu):
- 100 kA at 400/415V
- 75 kA at 690V
- Horsepower Ratings (UL/CSA):
- 1HP at 120V (1ph)
- 2HP at 240V (1ph)
- 1HP at 208V (3ph)
- 2HP at 240V (3ph)
- 5HP at 480V (3ph)
- 7-1/2HP at 600V (3ph)
8. Кепилдик жана колдоо
Schneider Electric products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Schneider Electric website. For technical assistance, product information, or support, please contact Schneider Electric customer service or visit their official support portal.
Онлайн ресурстар: www.se.com
