Introduction
Welcome to the user manual for the Connects2 CTSNS017.2 Steering Wheel Control Interface. This device is designed to allow you to retain the original steering wheel audio controls when upgrading your vehicle's head unit.
For optimal performance and safety, please read these instructions thoroughly before installation and use.
Продукт бүттүview
The Connects2 CTSNS017.2 is an automotive interface that integrates with your vehicle's existing wiring to provide seamless control of your aftermarket car stereo via the steering wheel buttons. It features OEM-specific connectors for a direct fit.
Продукт компоненттери
Image: The Connects2 CTSNS017.2 interface module (black box on the right) connected to various multi-pin wiring harnesses. The harnesses include white and black connectors designed to integrate with vehicle-specific wiring.
Шайкештик
This interface is specifically designed for select Nissan vehicles. Please verify your vehicle's make, model, and year against the list below to ensure compatibility.
- Nissan X-Trail (2001-2008)
- Nissan Almera (2000-2006)
- Nissan Primera (2001-2007)
- Nissan Terrano (2001-2006)
Important: Always refer to the official Connects2 compatibility guide or consult with a professional installer to confirm correct compatibility and installation for your specific vehicle model and aftermarket head unit.
Орнотуу жана орнотуу
Installation of the CTSNS017.2 requires technical knowledge of car audio wiring and vehicle electronics. It is highly recommended that installation be performed by a qualified professional.
Баштоодон мурун
- Ensure the vehicle's ignition is off and the battery's negative terminal is disconnected to prevent electrical shorts.
- Gather necessary tools (e.g., wire strippers, crimpers, electrical tape, trim removal tools).
- Identify the vehicle's original head unit wiring harness and the aftermarket head unit's wiring harness.
Орнотуу кадамдары (Жалпы көрсөтмө)
- Remove the original factory head unit from the dashboard.
- Locate the vehicle's original wiring harness.
- Connect the OEM-specific connectors of the CTSNS017.2 interface to the corresponding vehicle wiring harness. These connectors are designed for a direct fit.
- Connect the other end of the CTSNS017.2 interface (typically a multi-pin connector or flying leads) to the aftermarket head unit's steering wheel control input (often labeled "SWC," "Key1," "Key2," or "Remote In"). Refer to your aftermarket head unit's manual for specific wiring instructions.
- Бардык байланыштар коопсуз жана туура изоляцияланганын текшериңиз.
- Унаанын аккумуляторун кайра туташтырыңыз.
- Test the steering wheel controls with the new head unit. If controls are not functioning, refer to the troubleshooting section or the aftermarket head unit's manual for programming instructions.
- Carefully reassemble the dashboard, ensuring no wires are pinched.
Warning: Incorrect installation can lead to damage to the interface, head unit, or vehicle's electrical system. If you are unsure, seek professional assistance.
Иштөө нускамалары
Once correctly installed and configured, the Connects2 CTSNS017.2 interface operates automatically. Your vehicle's original steering wheel audio controls will now send signals to your aftermarket head unit, allowing you to control functions such as:
- Үнүн жогорулатуу/төмөндөтүү
- Track/Station Next/Previous
- Режим/Булакты тандоо
- Үнсүз
The specific functions supported may vary depending on your vehicle's original steering wheel controls and the aftermarket head unit's capabilities. Some aftermarket head units may require initial programming or learning of the steering wheel controls; refer to your head unit's manual for details.
Техникалык тейлөө
The Connects2 CTSNS017.2 interface is a sealed electronic component and requires no routine maintenance. Keep the unit free from moisture and extreme temperatures. Do not attempt to open or repair the unit, as this will void any warranty.
Проблемаларды чечүү
Орнотуудан кийин көйгөйлөргө туш болсоңуз, көйгөйлөрдү чечүүнүн төмөнкү кадамдарын карап көрүңүз:
- Руль дөңгөлөгүн башкаруу функциясы жок:
- Verify all connections are secure and correctly wired according to the installation instructions and your aftermarket head unit's manual.
- Ensure the aftermarket head unit's steering wheel control input is correctly connected to the interface.
- Check if your aftermarket head unit requires programming or "learning" of the steering wheel controls. Consult its manual.
- Confirm vehicle compatibility with the CTSNS017.2.
- Үзгүлтүктүү башкаруу:
- Байланыштын начар же дат баскандыгын текшерүү.
- Ensure proper grounding of the head unit and interface.
- Incorrect Button Function:
- This often indicates a need for programming or re-programming the steering wheel controls within your aftermarket head unit's settings.
If problems persist, contact Connects2 customer support or a professional car audio installer.
Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Модель номери | CTSNS017.2 |
| Бренд | Туташат2 |
| Продукт түрү | Рулду башкаруу интерфейси |
| Туташтыргыч түрү | OEM Specific |
| Салмагы | 100 г |
| Өлчөмдөрү (L x W x Y) | 30 x 25 x 5 см |
Кепилдик жана колдоо
For warranty information, please refer to the documentation provided with your purchase or visit the official Connects2 website. Connects2 is a leading brand in automotive accessories, known for designing specific interface solutions for major market brands since 1999.
For technical support or further assistance, it is recommended to visit the official Connects2 source to confirm compatibility and correct installation procedures.
