CGOLDENWALL 1500W Automatic Oil Press Machine

Introduction

This manual provides detailed instructions for the safe and efficient operation of your CGOLDENWALL 1500W Automatic Oil Press Machine, Model CNA 684A. Please read all instructions carefully before use to ensure optimal performance and longevity of the appliance. This machine is designed for extracting oil from various seeds and nuts using both cold and hot pressing methods.

Маанилүү коопсуздук нускамалары

• Always ensure the machine is properly grounded in accordance with local electrical safety standards.
• Do not immerse the machine body in water or any other liquid. Clean only the removable parts.
• Колдорду жана кенен кийимдерди иштөө учурунда кыймылдуу бөлүктөрдөн алыс кармаңыз.
• Use dry materials only. Wet materials can cause blockages and damage to the machine.
• Do not put scrap materials back into the hopper after pressing, as this can cause blockages.
• Unplug the machine from the power outlet when not in use, before cleaning, or during maintenance.
• Exercise caution as parts of the machine, especially the press chamber and rod, can become very hot during operation. Use insulated gloves when handling hot components.
• Бул шайман физикалык, сезүү же акыл-эс жөндөмү начар же тажрыйбасы жана билими жок адамдар (анын ичинде балдар) үчүн, эгерде алардын коопсуздугуна жооптуу адам тарабынан көзөмөлсүз же шайманды колдонуу боюнча көрсөтмө болбосо, колдонууга арналбайт.

Продукт бүттүview жана компоненттер

The CGOLDENWALL 1500W Automatic Oil Press Machine consists of several key components designed for efficient oil extraction. Understanding each part is crucial for proper operation and maintenance.

• Хоппер: Where raw materials are fed into the machine.
• Press Chamber & Press Bar: The core components where materials are squeezed to extract oil. Features a unique high-speed plasma pressing rod for higher oil yield.
• Oil Outlet: Where the extracted oil flows out.
• Residue Elbow: Where the pressed pulp (slag) is discharged.
• Башкаруу панели: Features temperature control, power switch, and pressing/reverse functions.
• Мотор: A 1500W commercial-grade motor designed for continuous operation.
• Container & Filter: For collecting the extracted oil and filtering impurities.
• туткалары: Жөнөкөй көчүрүү үчүн.

Орнотуу колдонмосу

Follow these steps for the initial setup of your oil press machine:

1. Таңылганын ачуу: Бардык компоненттерди таңгактан кылдаттык менен алып салыңыз.
2. Жайгашкан жери: Place the machine on a stable, flat, and heat-resistant surface. Ensure there is adequate ventilation around the unit.
3. Install Press Rod and Chamber: Insert the press rod into the press chamber, then attach the assembly to the machine body. Secure it with the provided fasteners.
4. Хопперди орнотуу: Place the hopper securely on top of the machine's feeding inlet.
5. Позиция контейнерлери: Place the oil collection container with the filter under the oil outlet and a separate container under the residue elbow.
6. Туташуу кубаты: Кубат шнурын жерге туташтырылган AC розеткага сайыңыз.

Иштөө нускамалары

1. Материалды даярдоо

The quality and yield of oil depend significantly on the preparation of raw materials. Ensure all materials are dry and free from moisture. Some materials may require pre-chopping into smaller pieces.

Ылайыктуу материалдар: Coconut, Sunflower Seed, Walnut, Okra, Soybean, Peanuts, Moringa Seed, Kiwi Seed, Winged Oil Fruit, Perilla Seed, Flax Seed, Camellia Seed, Rapeseed, Black Sesame, White Sesame, Almond Powder, Pepper Seeds, Pumpkin Seeds, Pine Nuts, Licorice.

Эскертүү: This machine is not recommended for pressing olive oil or fresh olives, fresh avocado, or fresh coconut. These materials require specific pre-processing (e.g., drying and crushing into kernels/pieces) to be suitable for extraction with this type of household press.

2. Preheating the Machine

Before starting the pressing process, the machine needs to be preheated to the optimal temperature.

1. Turn on the 'Heating' switch.
2. Set the desired temperature (usually around 200°C / 392°F for most materials).
3. Allow the machine to preheat for 8-10 minutes until the displayed temperature reaches the set temperature.

3. Oil Pressing Process

Once the machine is preheated, you can begin feeding the materials.

1. Turn on the 'Press' switch.
2. Slowly add a small amount of raw material into the hopper first.
3. After observing a normal flow of oil and residue, add a larger amount of material to the hopper.

The machine supports both hot and cold pressing. Hot pressing involves heating the material to 60-80°C before pressing, resulting in a richer aroma and higher oil yield (oil output around 60-75°C). Cold pressing directly processes fresh and dry ingredients without additional frying, yielding oil at about 40-50°C, which retains more natural nutrients.

4. Post-Pressing Oil Handling

Freshly pressed oil may contain fine particles. For clearer oil, it is recommended to let it settle.

• Freshly pressed oil contains protein and is not suitable for direct use immediately.
• It needs to be left for more than 24 hours to settle and clarify before consumption.

Тейлөө жана тазалоо

Proper cleaning and maintenance ensure the longevity and hygienic operation of your oil press machine.

1. Муздатуу: After oil extraction, turn off the heating switch and press the reverse switch for 30 seconds to clear any remaining material and allow the machine to cool down.
2. Бөлүп салуу: Carefully remove the hopper, lift the front cover, and then remove the screws to detach the press chamber and press bar. Use insulated gloves as parts may still be warm.
3. Таза компоненттери: Wash the removed components (press chamber, press bar, hopper, oil container, filter) with water and a brush to remove any oil residue. Ensure they are thoroughly dried.
4. Машина корпусу: Wipe the main machine body with a damp cloth. Do not rinse or immerse the main unit in water.
5. Lubrication (for long-term storage): If the machine will not be used for a long time, apply a little vegetable oil to the main parts of the press chamber and press bar before storing.
6. Сактагыч: Store all components in a dry and ventilated place.

Проблемаларды чечүү

Бул жерде кээ бир жалпы маселелер жана алардын мүмкүн болуучу чечимдери:

• Wet Residue: If the residue coming out is very wet, it indicates that the material might be too moist or the machine is not fully preheated. Stop feeding, press the reverse switch for 30 seconds to clear the chamber, then restart the press switch. Ensure materials are thoroughly dried before processing.
• Machine Jams: This can occur if materials are too large or too wet. Ensure materials like walnuts are chopped into small pieces. If a jam occurs, turn off the machine, unplug it, and carefully disassemble the press chamber and rod to clear the obstruction.
• Low Oil Yield: This can be due to insufficient preheating, overly wet materials, or the type of material being pressed. Ensure the machine is fully preheated and materials are dry. Refer to the oil yield table for expected yields for different materials.
• No Oil Output: Check if the machine is properly assembled and if the heating element is working. Ensure the press switch is engaged.

Техникалык шарттар

Technical details for the CGOLDENWALL 1500W Automatic Oil Press Machine (Model CNA 684A):

Кепилдик жана колдоо

CGOLDENWALL is committed to providing quality products and customer satisfaction.

• Кепилдик: This product typically comes with a 2-year warranty service. Please refer to your purchase documentation for specific warranty terms and conditions.
• Техникалык колдоо: For any technical assistance, operational questions, or warranty claims, please contact CGOLDENWALL customer support. Online technical support is available.
• Байланыш: You can find contact information on the official CGOLDENWALL дүкөнү or through the seller where you purchased the product.