Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of the SZDoit T101 Robot Tank Car Chassis. This kit is designed for educational and DIY robotics projects, offering a robust metal platform for integration with various microcontrollers such as Arduino, Raspberry Pi, and STM32. It is important to read through all instructions before beginning assembly.
Компоненттер камтылган
The following components are included in your SZDoit T101 Robot Tank Car Chassis kit:
- Panel: 1 piece (main chassis frame)
- Motor: 2 pieces (DC gear motors)
- Track: 2 pieces (plastic track chains)
- Bearing wheel: 2 pieces (plastic idler wheels)
- Driving wheel: 2 pieces (plastic drive wheels)
- Screw: 1 set (various fasteners for assembly)
Ассамблеянын колдонмосу
Follow these steps to assemble your robot tank car chassis. It is recommended to lay out all components before starting.
- Attach Motors to Chassis: Secure the two DC motors to the designated mounting points on the metal chassis panel using the provided screws. Ensure they are firmly attached.
- Install Driving Wheels: Mount the plastic driving wheels onto the motor shafts. These wheels will transmit power to the tracks.
- Install Bearing Wheels: Attach the plastic bearing wheels (idler wheels) to the opposite end of the chassis. These wheels help guide the tracks.
- Тректерди туташтыруу: Carefully wrap the plastic track chains around the driving and bearing wheels on each side. The tracks are designed to be adjustable in length. If a track is too long, individual joints can be removed using a small tool like tweezers.
Коопсуздук эскертүүсү
Exercise caution during assembly to prevent injury. Be mindful of small parts and sharp edges. Adult supervision is recommended for younger users.
Иштөө принциптери
The SZDoit T101 is a robot tank car chassis designed as a foundational platform. It does not include a controller or programming. To operate the chassis, you will need to integrate an external microcontroller (e.g., Arduino Uno R3, Raspberry Pi, NodeMCU, Microbit) and appropriate motor drivers and power supply.
The included DC motors operate within a voltage range of 6V to 12V. Ensure your power source and motor drivers are compatible with these specifications. The chassis is intended for scientific study and research, with a recommended bearing load of approximately 1-3 kg.
Техникалык тейлөө
Regular maintenance ensures the longevity and optimal performance of your robot tank chassis.
- Жолду текшерүү: Periodically check the plastic tracks for wear, damage, or debris. Ensure they are properly tensioned; adjust length if necessary as described in the assembly section.
- Мотор текшерүү: Listen for unusual noises from the motors during operation. Ensure motor connections are secure.
- Жалпы тазалоо: Keep the chassis free from dust and dirt, especially around moving parts and electrical connections.
Проблемаларды чечүү
Бул бөлүмдө сиз кездешиши мүмкүн болгон жалпы суроолор жана көйгөйлөр каралат.
- Track is too long: The track is composed of individual joints. You can adjust its length by carefully removing one or more joints using a small tool like tweezers.
- Motor not operating: Verify that the motor is receiving the correct voltage (6-12V DC) and that all electrical connections to the motor driver and power supply are secure. Ensure your controller is sending appropriate signals.
- Low bearing load capacity: This chassis is primarily designed for scientific study and light experimental setups. The typical bearing load is 1-3 kg. For applications requiring a significantly higher load, please consult the manufacturer for alternative solutions.
Техникалык мүнөздөмөлөр
Detailed specifications for the SZDoit T101 Robot Tank Car Chassis:
Продукт параметрлери
| Параметр | Нарк |
|---|---|
| Модел | T101 |
| Өлчөмү (L*W*H) | 18 x 13 x 7 см (болжол менен 193 x 163 x 60 мм) |
| Салмагы | 0.53 kg (approx. 0.47 kg for chassis only) |
| Трек материалы | Пластик |
| Motor Voltage Диапазон | 6-12В DC |
| Дөңгөлөк материалы | Metal (driving), Plastic (bearing) |
| Frame Material | 2 мм алюминий |
| Surface Treatment | Кум менен кычкылдандыруу |
| Max Suggested Weight | 5 kg (Manufacturer's Suggested) |
Wheel Parameters
| Параметр | Нарк |
|---|---|
| Driving Wheel Size | 48.03 x 31.85 мм |
| Bearing Wheel Size | 48 x 37 мм |
| Track Joints | 52 joints per track |
Motor Parameters (33GB-520 DC Gear Motor)
| Параметр | Нарк |
|---|---|
| Тtage Диапазон | 6V - 12V туруктуу ток |
| Rated Voltage | 12V DC |
| Жүк жок ылдамдык | 170 - 350 rpm (at 12V) |
| Жүктөлбөгөн ток | 100мА |
| Мотор салмагы | 100г |
Колдоо жана ресурстар
For additional documentation, source code, and video tutorials, please refer to the following resources:
- Онлайн документация: Detailed information and Arduino source code can be found on the official blog: gitnova.com
- Video Manuals: Издөө "TP101" on YouTube for various video assembly and usage guides.
If you encounter any issues or require further assistance, please contact SZDoit customer support.
