Introduction
This instruction manual provides detailed guidance for the installation, operation, and maintenance of your Everbilt 1 Pair Frameless 35 mm 110-Degree Full Overlay Nickel Cabinet Hinges. Please read this manual thoroughly before beginning installation to ensure proper function and longevity of the product.
Коопсуздук маалыматы
Always wear appropriate personal protective equipment, such as safety glasses, when working with tools and hardware. Keep small parts away from children. Ensure all screws are securely fastened to prevent injury or damage to the cabinet door.
Пакеттин мазмуну
Орнотууну баштоодон мурун бардык компоненттердин бар экенин текшериңиз. Эгерде кандайдыр бир тетиктер жок болсо же бузулган болсо, орнотууну улантпаңыз жана кардарларды колдоо кызматына кайрылыңыз.
- 2 x Everbilt 35 mm 110-Degree Full Overlay Cabinet Hinges
- Mounting Screws (quantity may vary, typically 8-12 screws)
Image: Two Everbilt 35mm 110-degree full overlay cabinet hinges are shown alongside a small pile of mounting screws. The hinges are made of nickel-plated steel, with one hinge in an open position and the other in a closed position, demonstrating their design and included hardware.
Орнотуу жана орнотуу
These hinges are designed for frameless cabinets with a full overlay door application. A 35mm cup hole is required in the cabinet door for hinge cup insertion.
Керектүү куралдар:
- 35 мм Forstner учу менен бургулоо
- Филлипс бурагыч
- Өлчөөчү лента же сызгыч
- Карандаш
Орнотуу кадамдары:
- Шкафтын эшигин даярдоо: Mark the positions for the 35mm hinge cup holes on the inside of the cabinet door. Typically, these are 3-4 inches from the top and bottom edges. Drill the 35mm cup holes to the appropriate depth (usually 1/2 inch or 13mm), ensuring not to drill through the door face.
- Илмектерди эшикке бекитүү: Insert the hinge cups into the drilled holes. Secure each hinge cup to the cabinet door using the provided small screws. Ensure the hinges are flush and straight.
- Prepare the Cabinet Frame/Side Panel: For full overlay applications on frameless cabinets, the hinge mounting plate attaches directly to the inside of the cabinet side panel. Measure and mark the corresponding screw hole positions on the cabinet side panel, aligning with the hinges attached to the door.
- Mount Door to Cabinet: Align the hinges with the marked positions on the cabinet side panel. Secure the hinge mounting plates to the cabinet using the provided larger screws.
- Эшикти жөндөө: These hinges offer 3-way adjustability (side-to-side, depth, and height) to ensure perfect door alignment.
- Капталдан тууралоо: Use the screw closest to the cabinet edge to move the door left or right.
- Тереңдикти жөндөө: Use the screw further from the cabinet edge to move the door in or out from the cabinet face.
- Бийиктигин тууралоо: Loosen the mounting screws slightly, adjust the door up or down, then re-tighten.
Image: A cross-sectional diagram illustrating a full overlay hinge. It shows how the cabinet door completely covers the cabinet frame when closed, with the hinge mechanism positioned between the door and the cabinet side panel, demonstrating the "Full Overlay" concept.
Image: A single Everbilt 35mm 110-degree full overlay cabinet hinge is displayed. The hinge is made of nickel-plated steel, showing its cup, arm, and mounting plate components, ready for installation.
Иштеп жатат
Once installed and adjusted, the Everbilt 110-Degree Full Overlay Hinges allow the cabinet door to open smoothly to a 110-degree angle. The hinges are designed for quiet operation and provide a full overlay appearance, meaning the door completely covers the cabinet opening and frame when closed.
Техникалык тейлөө
These hinges require minimal maintenance. Periodically check all mounting screws to ensure they remain tight. If the door alignment shifts over time, refer to the "Adjust the Door" section under "Setup and Installation" to re-align. Clean hinges with a soft, damp кездеме; абразивдүү тазалагычтардан качыңыз.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Door not closing properly or sagging | Loose mounting screws or improper adjustment. | Tighten all mounting screws. Adjust side-to-side and height screws as needed. |
| Door rubbing against cabinet | Incorrect door alignment. | Use the side-to-side adjustment screw on the hinge to move the door away from the rubbing point. |
| Door not flush with cabinet face | Depth adjustment needed. | Adjust the depth screw on the hinge to pull the door closer to or push it further from the cabinet face. |
Техникалык шарттар
- Продукт түрү: Frameless Cabinet Hinge
- Модель номери: HC11SFE-NP-CP
- Overlay Type: Толук катмар
- Ачылышы: 110 градус
- Чөйчөктүн диаметри: 35 мм
- Бүтүрүү: Никель менен капталган
- Жөнгө салуу: 3-Way (Side-to-side, Depth, Height)
- Материал: Болот
- Пакеттин мазмуну: 2 Hinges, Mounting Screws
Кепилдик жана колдоо
For information regarding product warranty or technical support, please refer to the Everbilt official webсайтка же кардарларды тейлөө бөлүмүнө кайрылыңыз. Кепилдик дооматтар үчүн сатып алуу дүмүрчөгүңүздү сактаңыз.
Note: Specific warranty details are not provided in this manual.
