VOLTCRAFT LWT-100 (TDS) Conductivity Meter User Manual

1. Продукт бүтүп калдыview

The VOLTCRAFT LWT-100 is a high-quality conductivity meter designed for rapid determination of conductivity, salinity, and Total Dissolved Solids (TDS) values in various liquids. Featuring a superior graphite measuring cell and IP67 water resistance, this device ensures accurate and reliable measurements in demanding environments.

Сүрөт 1: Алдыңкы view of the LWT-100 Conductivity Meter. The device features a clear digital display showing conductivity and temperature readings, along with intuitive control buttons for navigation.

2. Коопсуздук маалыматы

Please read and understand all safety instructions before operating the device. Failure to do so may result in injury or damage to the meter.

• Do not immerse the entire device in water beyond its IP67 rating. The measuring cell is designed for liquid contact, but the main body should be protected from excessive moisture.
• Түзмөктү түшүрүп алуудан же катуу соккуга кабылтуудан алыс болуңуз.
• Аппаратты ачууга же оңдоого аракет кылбаңыз. Бардык тейлөөлөрдү квалификациялуу кызматкерлерге тапшырыңыз.
• Балдар жетпеген жерде сактаңыз.
• Clean the measuring cell carefully as described in the Maintenance section.

3. Продукциянын компоненттери

The VOLTCRAFT LWT-100 package typically includes:

• 1 x VOLTCRAFT LWT-100 Conductivity Meter
• Колдонуучунун Колдонмосу (бул документ)

2-сүрөт: Артка view of the LWT-100 Conductivity Meter. The rear label provides essential product information, including the model name, measurement range, and serial number.

4. Орнотуу

The VOLTCRAFT LWT-100 is designed for immediate use. It operates on an internal power source and does not require user-replaceable batteries. Follow these steps for initial setup:

1. Пакеттен чыгаруу: Carefully remove the meter from its packaging.
2. Алгачкы текшерүү: Check the device for any visible damage. If damaged, do not use and contact customer support.
3. Күйгүзүү: Press the power button (usually indicated by a power symbol or a specific button on the front panel) to turn on the device. The display should illuminate.
4. Өзүн-өзү сыноо: The device may perform a brief self-test upon startup. Wait for the display to show stable readings or a ready indicator.

5. Иштөө нускамалары

The LWT-100 allows for quick and accurate measurement of conductivity, salinity, and TDS. Ensure the measuring cell is clean before each use.

Figure 3: Close-up of the LWT-100 display. The screen clearly shows the measured conductivity in microSiemens (µS) and the corresponding temperature in degrees Celsius (°C).

5.1 Ченөө

1. Даярдоо Сampле: Ensure the liquid sample is at a stable temperature and free of large particles that could obstruct the sensor.
2. Immerse Sensor: Carefully immerse the graphite measuring cell (located at the bottom of the device) into the liquid sample. Ensure the sensor is fully submerged and no air bubbles are trapped around it.
3. Окуу дисплей: Wait for the reading on the display to stabilize. The device will show the conductivity value (e.g., in µS/cm or mS/cm) and the temperature.
4. Маалыматтарды жаздыруу: Note down the measured values as needed.
5. Таза сенсор: After each measurement, rinse the measuring cell with distilled or deionized water to prevent contamination and residue buildup.

5.2 Changing Measurement Modes (if applicable)

The LWT-100 can measure conductivity, salinity, and TDS. Use the designated mode button (refer to the button labels on your device, typically indicated by an arrow or 'MODE' symbol) to cycle through the available measurement modes. The active mode will be indicated on the display.

6. Техникалык тейлөө

Proper maintenance ensures the longevity and accuracy of your VOLTCRAFT LWT-100.

• Cleaning the Measuring Cell: After each use, rinse the graphite measuring cell thoroughly with distilled or deionized water. For stubborn residues, gently wipe the electrodes with a soft, lint-free cloth. Do not use abrasive materials or harsh chemicals.
• Аппараттын корпусун тазалоо: Аппараттын сыртын жумшак, г менен сүртүңүзamp кездеме. Эриткичтерди же күчтүү жуучу каражаттарды колдонбоңуз.
• Сактагыч: Store the meter in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure the measuring cell is clean and dry before storage.
• Калибрлөө: While the LWT-100 is designed for high accuracy, periodic calibration with known conductivity standards may be required for critical applications. Refer to specific calibration instructions if provided with your device or consult VOLTCRAFT support.

7. Кыйынчылыктарды

If you encounter issues with your LWT-100, refer to the following common problems and solutions:

8. Техникалык шарттар

9. Колдоо маалыматы

For technical support, warranty claims, or spare parts availability, please contact VOLTCRAFT customer service. Refer to the official VOLTCRAFT webБайланыш маалыматы үчүн сайтка же сатып алуу документтериңизге кайрылыңыз.

Запастык бөлүктөрдүн жеткиликтүүлүгү: 1 жыл.