Satco 80-2627 Two-Light Ballast Bypass Wiring Harness Instruction Manual

1. Киришүү

This manual provides essential instructions for the safe and correct installation, operation, and maintenance of the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness. This harness is designed to convert existing fluorescent fixtures to operate with linear LED T8 lamps that require a ballast bypass (direct wire) installation. Please read all instructions thoroughly before beginning installation.

2. Коопсуздук маалыматы

WARNING: Risk of electric shock. Installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.

Always disconnect power at the circuit breaker or fuse box before installation, servicing, or removing the fixture.
камсыз кылуу voltage is correct for the LED T8 lampс орнотулууда.
Комплектти орнотуу учурунда зымдарды же электрдик тетиктердин корпусунда ачык тешиктерди жасабаңыз же өзгөртпөңүз.
Зымдарга зыян келтирбөө үчүн, зымдарды металл же башка учтуу нерселердин четтерине тийгизбеңиз.
This product is intended for use with specific LED T8 lamps designed for ballast bypass operation. Consult the LED lamp manufacturer's instructions for compatibility and wiring diagrams.
Орнотуу учурунда коопсуздук көз айнеги жана кол кап сыяктуу тиешелүү жеке коргонуу каражаттарын (ЖКК) кийиңиз.
Бардык байланыштар коопсуз жана туура изоляцияланганын текшериңиз.

3. Продукт бүтүп калдыview

The Satco 80-2627 wiring harness simplifies the conversion of a two-lamp fluorescent fixture to operate with ballast bypass LED T8 lamps. It includes pre-wired lamp holders (sockets) and a quick-connect terminal for easy connection to the main power supply.

Satco 80-2627 Ballast Bypass Wiring Harness Components

Image 1: Components of the Satco 80-2627 Ballast Bypass Wiring Harness, showing the pre-wired lamp holders and quick-connect terminal.

4. Орнотуу жана орнотуу

Follow these steps carefully to install the Satco 80-2627 wiring harness:

Кубатты өчүрүү: Turn off power to the fixture at the circuit breaker or fuse box. Verify power is off using a voltagулантуудан мурун электрондук сыноочу.
Access Fixture Wiring: Open the fixture to access the existing ballast and wiring. Remove any covers or diffusers as necessary.
Remove Existing Ballast: Disconnect all wires from the existing fluorescent ballast. Carefully remove and dispose of the old ballast according to local regulations.
Жаңы L орнотууamp Ээлери: Бар болгон лamp holders (sockets) from the fixture. Install the new pre-wired lamp holders from the Satco 80-2627 harness into the fixture, ensuring they are securely seated.

Image 2: Illustration of the easy installation process, showing the harness with new lamp holders ready for connection.
Wire the Harness: Connect the quick-connect terminal of the Satco 80-2627 harness to the fixture's main power supply wires (Line and Neutral). Ensure proper polarity as indicated by the wiring diagram on the LED T8 lamps or fixture. Typically, one side of the LED T8 lamp receives Line voltage, and the other side receives Neutral. The harness is designed to provide these connections to the lamp ээлери.
Коопсуз зымдар: Ensure all wiring is neatly routed and secured, preventing pinching or contact with sharp edges. Replace any wiring covers.
Install LED T8 Lamps: Insert the ballast bypass LED T8 lamps into the new lamp holders. Ensure they are fully seated and twisted into place.
Close Fixture: Replace any fixture covers or diffusers that were removed.
Күчтү калыбына келтирүү: Turn power back on at the circuit breaker or fuse box. Test the new LED lighting system.

5. Иштөө нускамалары

Once installed, the Satco 80-2627 Ballast Bypass Wiring Harness operates seamlessly with your fixture's existing wall switch. Simply use the wall switch to turn the LED T8 lampкүйгүзүү же өчүрүү.

6. Техникалык тейлөө

The Satco 80-2627 wiring harness requires minimal maintenance. Periodically, it is recommended to:

Визуалдык текшерүү: With power disconnected, visually inspect the wiring and connections for any signs of wear, damage, or loose connections.
Тазалоо: If necessary, gently wipe down the exterior of the lamp holders with a dry, lint-free cloth. Do not use liquid cleaners near electrical components.

7. Кыйынчылыктарды

Орнотуудан кийин көйгөйлөргө туш болсоңуз, көйгөйлөрдү чечүү боюнча төмөнкү колдонмону караңыз:

Көйгөй	Мүмкүн себеп	Чечим
Lampс күйгүзбөйт.	Шайманга күч жок. Бошогон зымдар байланышы. Туура эмес зым. Faulty LED T8 lamp.	Автоматтык өчүргүчтү/ сақтандыргычты текшериңиз. Verify all connections are secure (power off). Review installation steps and wiring diagram (power off). Test with a known good LED T8 lamp.
Lampжымыңдайт же күңүрт.	Loose lamp connection in socket. Incompatible LED T8 lamp (not ballast bypass type). Faulty LED T8 lamp.	камсыз кылуу лamps are fully seated and twisted. Confirm LED T8 lamps are specifically for ballast bypass applications. Replace the LED T8 lamp.

If troubleshooting steps do not resolve the issue, contact a qualified electrician or Satco customer support.

8. Техникалык шарттар

Модель номери: 80-2627
Өндүрүүчү: Сатко
Бөлүмдүн номери: 80-2627
Продукциянын өлчөмдөрү: Болжол менен 10 x 10 x 10 дюйм (таңгактоо)
Элемент Салмагы: 1 фунт
Кубат булагы: Электр зымдары
Л саныamps Колдоого алынган: Эки (2)
Туура келген Лamp Түрү: Linear LED T8 Lamps (Ballast Bypass / Direct Wire)
Камтылган компоненттер: Satco 80-2627 Two Light Ballast Bypass Wiring Harness

9. Кепилдик маалыматы

For warranty information regarding the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness, please contact the manufacturer directly. Warranty terms and conditions may vary.

Өндүрүүчүнүн байланышы: Refer to Satco's official webакыркы байланыш маалыматы үчүн сайт же продукт таңгак.

10. Колдоо

If you require further assistance or have questions not covered in this manual, please contact Satco customer support. Ensure you have your product model number (80-2627) available when contacting support.

Сатко Webсайт: www.satco.com