iBeam by Metra TEDGH Ram Tailgate туткасы бар камера колдонуучусунун колдонмосу

Introduction

Бул колдонмодо Metra TEDGH Ram арткы эшиктин туткалуу камерасын орнотуу, иштетүү жана тейлөө боюнча кеңири көрсөтмөлөр берилген. Бул заводдон алмаштырылган арткы эшиктин туткалуу камерасы унааңыздын артындагы көрүнүүнү жакшыртуу жана тунук көрүнүштү камсыз кылуу үчүн иштелип чыккан. view for safer maneuvering and parking.

Продукт бүттүview

The iBeam TEDGH camera integrates seamlessly into your Ram truck's tailgate handle, providing a discreet and factory-like appearance. It features advanced imaging capabilities for both day and night use.

• Жогорку сапаттагы сүрөттөө: Equipped with a 1/3 inch CMOS camera sensor for sharp and clear video output.
• Wide Viewбурч: 150 градус сунуш кылат viewing angle to capture a broad perspective behind the vehicle.
• Түнкү көрүнүш: Features 0.5 LUX night vision for improved visibility in low-light conditions.
• Defeatable Parking Lines: Includes on-screen parking guidelines that can be enabled or disabled as per user preference.
• Extended Harness: Comes with a 26-foot harness for flexible connection to an aftermarket radio or display (not included).

Кутуда эмне бар

Upon opening the product packaging, please ensure all the following components are present:

• iBeam TEDGH Ram Tailgate Handle Camera unit
• 26-foot extension cable harness
• Колдонуучунун Колдонмосу (бул документ)

Орнотуу жана орнотуу

The iBeam TEDGH camera is designed for surface mount installation as a factory replacement tailgate handle. Professional installation is recommended.

Коопсуздук чаралары

• Орнотууну баштоодон мурун, электрдик кыска туташуулардын алдын алуу үчүн унаанын аккумуляторун сууруп алыңыз.
• Ensure all wiring is routed away from moving parts, heat sources, and sharp edges.
• Бардык байланыштар коопсуз жана туура изоляцияланганын текшериңиз.
• This product is intended for use with a 12-volt DC power supply.

Installation Steps (General Guide)

1. Remove Existing Tailgate Handle: Carefully remove the original tailgate handle from your Ram truck. Refer to your vehicle's service manual for specific instructions.
2. Install New Tailgate Handle Camera: Mount the iBeam TEDGH camera unit into the tailgate opening, ensuring it is securely fastened.
3. Маршрут зымдары: Route the 26-foot extension cable from the camera through the tailgate and chassis to the location of your aftermarket radio or display. Ensure the cable is protected from damage.
4. Дисплейге туташуу: Connect the video output cable from the camera harness to the video input of your aftermarket radio or monitor.
5. Кубат туташуу: Connect the power wires of the camera harness to a suitable 12-volt power source, typically the vehicle's reverse light circuit, so the camera activates when the vehicle is in reverse.
6. Сыноо функциясы: Reconnect the vehicle's battery and test the camera's operation. Engage reverse gear and verify that the camera image appears on your display.
7. Коопсуз зымдар: Once confirmed operational, secure all wiring with zip ties or electrical tape to prevent rattling or damage.

Figure 1: The iBeam TEDGH Ram Tailgate Handle Camera, showing the integrated camera lens on the left side of the handle and the attached wiring harness on the right.

Figure 2: A closer front view of the iBeam TEDGH Ram Tailgate Handle Camera, highlighting the camera lens and the handle mechanism.

Иштөө нускамалары

The iBeam TEDGH camera operates automatically when the vehicle is placed into reverse gear, provided it is correctly wired to the reverse light circuit or a switched 12V source that activates with reverse.

• Автоматтык иштетүү: When you shift your vehicle into reverse, the camera will automatically display the rear view on your connected aftermarket monitor.
• Паркинг линиялары: The camera features integrated parking lines to assist with judging distance and alignment. These lines are defeatable, meaning they can be turned on or off. The method for defeating (enabling/disabling) parking lines typically involves cutting a specific wire loop on the camera harness during installation. Consult the wiring diagram provided with the product for exact instructions.
• Түнкү көрүнүш: The 0.5 LUX night vision capability allows for clear visibility even in very low light conditions, enhancing safety during nighttime parking or maneuvering.

Техникалык тейлөө

To ensure optimal performance and longevity of your iBeam TEDGH camera, follow these simple maintenance guidelines:

• Линзаны тазалоо: Дайыма камеранын линзасын жумшак, гamp cloth to remove dirt, dust, and debris that may obstruct the viewАбразивдүү тазалоочу каражаттардан же линзаны чийип салуучу материалдардан алыс болуңуз.
• Зымдарды текшерүү: Periodically check the wiring and connections for any signs of wear, fraying, or corrosion. Ensure all connections remain secure.
• Жогорку басымдагы жуудан алыс болуңуз: When washing your vehicle, avoid directing high-pressure water jets directly at the camera lens or housing, as this could potentially damage the seal or internal components.

Проблемаларды чечүү

If you encounter issues with your iBeam TEDGH camera, refer to the following common troubleshooting steps:

Техникалык шарттар

Кепилдик маалымат

iBeam products are manufactured by Metra Electronics Corp. For specific warranty details, including coverage period and terms, please refer to the warranty card included with your product or visit the official Metra Electronics webсайт. Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.

Кардарларды колдоо

Should you require further assistance, technical support, or have questions not covered in this manual, please contact Metra Electronics Corp. customer support. Contact information can typically be found on their official webсайтында же продуктунун таңгагында.

Manufacturer: Metra Electronics Corp