LICHIFIT 4100E 2.4G 4-Channel Micro Receiver Instruction Manual

1. Продукт бүтүп калдыview

The LICHIFIT 4100E is a compact 2.4GHz 4-channel micro receiver designed for use with JR and SPEKTRUM DSM2 compatible transmitters. This receiver is suitable for various remote-controlled models, offering reliable signal reception in a lightweight package.

1-сүрөт: LICHIFIT 4100E 2.4G 4-Channel Micro Receiver. This image shows the compact receiver board with its antenna and pin connectors.

2. Негизги өзгөчөлүктөрү

• Шайкештик: Designed for JR / SPEKTRUM DSM2 transmitters (e.g., DX6I, DX7, DX8, DSX7, DSX9, DSX11).
• Модуляция: DSM2
• Топ: 2.4 ГГц
• Каналдар: 4
• Компакт өлчөмдөрү: Approximately 29mm x 16mm x 7mm.
• Жеңил салмак: Болжол менен 3 г.
• Тtage диапазону: 3.6V - 10V.
• Антеннанын узундугу: 29мм.

3. Орнотуу жана байлоо боюнча нускамалар

To establish communication between your LICHIFIT 4100E receiver and a compatible DSM2 transmitter, follow these binding steps:

1. Connect the Bind Plug: Insert the bind plug into the "BIND" port on the receiver. Ensure the plug is fully seated and correctly oriented. The negative pin is typically the furthest from the board.


2-сүрөт: Bind Plug. This plug is used to put the receiver into binding mode.

2. Ресиверди кубат: Connect a power source (e.g., battery or ESC with BEC) to any available channel port on the receiver. The receiver's LED should begin to flash rapidly, indicating it is in binding mode. If the LED only "blips" or does not flash, check the power connection and bind plug orientation. A steady LED indicates a successful connection, not binding mode.
3. Activate Transmitter Bind Mode: Turn on your compatible DSM2 transmitter while holding its bind button or activating its bind function (refer to your transmitter's manual for specific instructions).
4. Complete Binding: The receiver's LED should change from rapidly flashing to solid, indicating a successful bind.
5. Байланыштыруучу сайгычты алып салуу: Once the LED is solid, disconnect the power from the receiver, then remove the bind plug from the "BIND" port.
6. Сыноо байланышы: Reconnect power to the receiver (without the bind plug). The LED should illuminate solid, confirming the bind. Test all control surfaces and functions to ensure proper operation.

Эскертүү: Some users have reported that the receiver may require re-binding if the battery is disconnected for an extended period or if the power cycle is interrupted during initial setup. Always verify the solid LED indicator after powering on.

4. Иштөө нускамалары

After successful binding, connect your servos and Electronic Speed Controller (ESC) to the corresponding channels on the receiver. The LICHIFIT 4100E provides 4 channels for various control functions.

• Channel Connections: Connect servos for ailerons, elevator, rudder, and the ESC for throttle control to the appropriate channel pins. Refer to your model's specific wiring diagram.
• Күйгүзүү ырааттуулугу: Always turn on your transmitter first, then power on the receiver. When powering off, disconnect power from the receiver first, then turn off the transmitter.
• Диапазон текшерүү: Before flight or operation, perform a range check according to your transmitter's instructions to ensure a stable connection.

5. Техникалык тейлөө

Туура техникалык тейлөө сиздин кабыл алгычыңыздын узак мөөнөттүү жана ишенимдүү иштешин камсыз кылат.

• Кургак кармоо: The receiver is not water-resistant. Avoid exposure to moisture, humidity, and liquids.
• Тазалык: Кабыл алгычты чаңдан, кирден жана таштандылардан таза кармаңыз. Тазалоо үчүн жумшак, кургак щетканы же кысылган абаны колдонуңуз.
• Физикалык коргоо: Protect the receiver from physical impact and vibrations. Mount it securely within your model.
• Антеннага кам көрүү: Ensure the antenna is not cut, kinked, or damaged. Proper antenna placement is crucial for optimal range.

6. Кыйынчылыктарды

• Receiver Not Binding / LED Blips:
  • Ensure the bind plug is fully inserted into the "BIND" port.
  • Verify the bind plug's orientation; the negative pin is typically furthest from the board.
  • Check power connections to the receiver. Ensure sufficient voltage (3.6-10V).
  • Confirm your transmitter is in DSM2 mode and its bind function is correctly activated.
• Loss of Binding After Power Cycle:
  • Some units may require re-binding if power is disconnected. Perform the binding procedure again.
  • Ensure the bind plug is removed мурун disconnecting power after a successful bind.
• Башкаруу жообу жок:
  • Confirm the receiver is successfully bound (solid LED).
  • Check all servo and ESC connections to the correct channels.
  • Verify that servos and ESCs are receiving power.
  • Ensure your transmitter is powered on and functioning correctly.
• Чектелген диапазон:
  • Check for damage to the receiver antenna.
  • Ensure the antenna is positioned optimally and not shielded by carbon fiber or metal components.
  • Avoid operating in areas with high 2.4GHz interference.

7. Техникалык шарттар

8. Кепилдик жана колдоо

Information regarding product warranty and direct customer support for the LICHIFIT 4100E receiver was not provided in the available product data. Please refer to your retailer or point of purchase for specific warranty terms and support options.