Elmchee FFR0001 Electric Foot Callus Remover Kit User Manual

Introduction

Welcome to the user manual for your Elmchee Electric Foot Callus Remover Kit. This guide provides essential information for safe and effective use, maintenance, and care of your device. Please read all instructions carefully before first use and retain this manual for future reference.

Коопсуздук маалыматы

• Do not use on skin for more than 2-3 seconds in one area to prevent irritation or injury.
• Close the product after each use.
• Clean the grinding head immediately after use.
• Ensure the grinding head is properly installed before operating the device.
• Do not submerge the device in water for extended periods, despite its waterproof design.
• Use only a 5V/1A charging voltage to avoid affecting the service life of the battery.

Кутуда эмне бар

Your Elmchee Electric Foot Callus Remover Kit includes the following items:

• Electric Foot Callus Remover Device
• USB заряддоо кабели
• 3 Replaceable Grinding Heads (Fine, Medium, Rough)
• Тазалоочу щетка
• User Manual

Жайгашуу

Аппаратты заряддоо

Before initial use, fully charge your device. The high-quality 1200mAh lithium battery features overcharge protection and a battery display function, allowing you to monitor the remaining charge. A full charge takes approximately 3 hours and provides about 90 minutes of continuous operation. Ensure you use a 5V/1A charging voltage to maintain battery health.

Attaching/Replacing Grinding Heads

The kit includes three different quartz sand grinding heads: a rough grinding head for stubborn horny dead skin, a medium grinding head for rough dead skin, and a fine grinding head for daily care. Select the appropriate head based on your skin's condition.

1. Hold the main body of the device.
2. Press the body switch key.
3. Press the grinding head switch key and pull out the head with one hand to remove.
4. Align the new grinding head and push it into place until it clicks securely.

Иштөө нускамалары

Даярдоо

For best results, first clean your feet or soak them in warm water for 10 minutes to soften the skin. Then, thoroughly dry your feet before using the device.

Колдонуу

The Electric Foot Callus Remover offers two speeds: 1700x/min for low speed and 2000x/min for high speed. Select the desired speed by pressing the power button. Gently rub the chosen grinding head over the dead skin until it is removed. The device is designed to automatically stop if too much pressure is applied, preventing damage to healthy skin.

Пост-колдонуу

After removing dead skin, wipe your feet with a dry cloth. Apply a moisturizing cream and gently massage your feet to hydrate and soothe the skin.

Техникалык тейлөө

Тазалоо

The electric foot file has an IPX7 waterproof design, allowing the entire body to be rinsed under running water. After each use, close the product and clean the grinding head thoroughly. Do not soak the device in water for a long time.

Сактагыч

Store the product in a dry and well-ventilated area, away from direct sunlight and extreme temperatures.

Проблемаларды чечүү

• Device stops working during use: The device is equipped with a safety feature that automatically stops operation if excessive pressure is applied. This prevents damage to healthy skin. Reduce pressure and restart the device.
• Түзмөк күйбөй жатат: Ensure the device is fully charged. Check the LED power display for battery level. If the battery is low, connect the device to a 5V/1A power source using the provided USB cable for 3 hours.
• Ineffective callus removal: Ensure you are using the appropriate grinding head for your skin type (fine, medium, or rough). For very thick calluses, the rough grinding head is recommended. Make sure your feet are clean and dry before use.

Техникалык шарттар

Кепилдик жана колдоо

Your Elmchee callus remover kit comes with a one-year warranty. If you encounter any problems during use, please contact us in time, and we will provide you with satisfactory after-sales service. Please refer to your purchase documentation for specific contact details.