EVIL ENERGY 6AN Fuel Line Kit Instruction Manual

1. Киришүү

This manual provides detailed instructions for the proper installation, operation, and maintenance of your EVIL ENERGY 6AN Nylon Braided Fuel Line Kit. This kit is designed for various automotive fluid transfer applications, offering durability and performance. Please read this manual thoroughly before installation to ensure correct usage and safety.

Image 1.1: The EVIL ENERGY 6AN Fuel Line Kit, including the 20-foot braided hose and a variety of AN fittings.

2. Коопсуздук маалыматы

Working with automotive fuel systems and fluids requires caution. Always adhere to the following safety guidelines:

• Кандайдыр бир ишти баштоонун алдында унаанын кыймылдаткычы өчүрүлүп, муздатылганын текшериңиз.
• Disconnect the battery to prevent accidental electrical discharge.
• Relieve fuel system pressure before disconnecting any fuel lines. Consult your vehicle's service manual for specific procedures.
• Коопсуздук көз айнектерин жана химиялык заттарга туруктуу кол каптарды кошо алганда, тиешелүү жеке коргонуу каражаттарын (ЖКК) кийиңиз.
• Ачык оттон, учкундан же башка тутандыруу булактарынан алыс, жакшы желдетилген жерде иштеңиз.
• Өрт өчүргүч даяр болушу керек.
• Properly dispose of any spilled fluids or old components according to local regulations.
• Эгер кандайдыр бир кадамга ишенбесеңиз, квалификациялуу автотехникке кайрылыңыз.

3. Пакеттин мазмуну

Пакетти ачканда бардык компоненттер бар экенин жана бузулбаганын текшериңиз:

• 1x 6AN Braided Fuel Line (20 Feet)
• 4x 6AN Straight Swivel Hose Ends
• 2x 6AN 45-Degree Swivel Hose Ends
• 2x 6AN 90-Degree Swivel Hose Ends
• 2x 6AN 180-Degree Swivel Hose Ends
• 2x 6AN Hose Separator Clamps

Image 3.1: Visual representation of the components included in the kit, such as the hose, various angle fittings, and hose clamps.

4. Продукттун спецификациялары

Сүрөт 4.1: Детальдуу view of the 6AN hose dimensions, including ID (0.31") and OD (0.56").

Image 4.2: Cross-section illustrating the hose construction: CPE synthetic rubber inner, stainless steel wire mesh, and nylon outer braid.

Image 4.3: Key performance parameters of the 6AN hose, including 750psi working pressure, 2250psi burst pressure, and a temperature range of -22°F to 248°F.

5. Fluid Compatibility

The EVIL ENERGY 6AN braided fuel hose is compatible with a wide range of automotive fluids:

• Трансмиссиялык суюктук
• Мотор майы
• Race Gas
• Вакуум
• Гидравликалык суюктук
• Дизель майы
• Standard Automotive Fuel
• Муздаткыч

Important Note: This hose is NOT compatible with E85, E10, or methanol fuels.

Сүрөт 5.1: Мисamples of compatible mediums for the fuel line, including diesel, E15 gasoline, antifreeze, and various lubricants.

6. Орнотуу боюнча нускамалар

Follow these steps for proper assembly and installation of the 6AN fuel line kit:

6.1. Hose Preparation and Cutting

1. Measure the required length of the hose carefully.
2. Wrap the cutting area of the hose tightly with electrical tape to prevent fraying of the nylon braid.
3. Using a sharp hose cutter or fine-tooth saw, cut the hose squarely through the taped section. Ensure a clean, straight cut.
4. Remove the tape and clean any debris from the cut end.

6.2. Fitting Assembly

5. Unscrew the fitting's socket (outer nut) from the nipple (inner part).
6. Insert the cut end of the hose into the socket. Push firmly until the hose bottoms out against the threads inside the socket.
7. Apply a small amount of AN fitting lubricant or clean engine oil to the nipple threads.
8. Carefully thread the nipple into the hose and socket assembly. Ensure the hose does not back out of the socket.
9. Tighten the nipple into the socket using two AN wrenches (one to hold the socket, one to turn the nipple) until snug. Do not overtighten.
10. Inspect the assembly for any exposed braid or improper seating.

6.3. Hose Separator Clamp Орнотуу

11. Position the hose separator clamps along the hose run where needed to maintain proper spacing and prevent rubbing.
12. clampберилген жабдыктарды колдонуу.

Image 6.1: Step-by-step visual guide for hose cutting, inserting the hose into the fitting socket, threading the nipple, and final assembly.

Сүрөт 6.2: Visual examples of the 6AN fuel line kit installed in different automotive engine compartments, demonstrating typical applications.

7. Операциялык кароо

Орнотулгандан кийин, унааны иштетүүдөн мурун төмөнкү текшерүүлөрдү жүргүзүңүз:

• Агып кетүүнү текшерүү: With the engine off, cycle the ignition key to pressurize the fuel system (if applicable) and visually inspect all connections for any signs of leaks. For oil or coolant lines, start the engine and monitor for leaks.
• Текшерүү: Ensure the hose and fittings do not rub against any moving parts, sharp edges, or hot components. Adjust routing as necessary.
• Коопсуз орнотуу: Confirm all hose separator clamps and mounting points are secure.

During initial operation, periodically check the lines for leaks or signs of wear, especially after the first few driving cycles.

8. Техникалык тейлөө

Regular maintenance helps ensure the longevity and safe operation of your fuel line kit:

• Визуалдык текшерүү: Periodically inspect the entire length of the hose and all fittings for signs of wear, cracks, abrasions, or leaks. Pay close attention to areas near heat sources or moving parts.
• Тазалык: Keep the hose and fittings clean from dirt, grime, and corrosive substances. Use a mild detergent and water if cleaning is necessary.
• Тыюулугун текшерүү: Occasionally check the tightness of the AN fittings. Do not overtighten.
• Шланг багыты: Ensure the hose remains properly routed and secured by the separator clamps. Adjust if any shifting has occurred.

9. Кыйынчылыктарды

If you encounter issues with your EVIL ENERGY 6AN Fuel Line Kit, consider the following:

9.1. Leaks at Fittings

• Себеби: Improper assembly, insufficient tightening, damaged threads, or incorrect hose cut.
• Чечим: Disassemble the fitting, inspect threads for damage, ensure the hose is fully seated in the socket, re-lubricate threads, and reassemble, tightening to the recommended torque (snug, not excessive). If threads are damaged, replace the fitting.

9.2. Hose Fraying

• Себеби: Improper cutting technique, rubbing against other components.
• Чечим: Ensure proper cutting technique with tape. If fraying occurs during use, re-route the hose to prevent contact with abrasive surfaces or sharp edges. Use hose separator clamps to maintain clearance.

9.3. Restricted Flow

• Себеби: Kinked hose, debris inside the line.
• Чечим: Inspect the hose for kinks and re-route if necessary, ensuring the minimum bend radius is not exceeded. If debris is suspected, disconnect and flush the line.

10. Кепилдик жана колдоо

EVIL ENERGY products are manufactured to high-quality standards. For warranty information, technical support, or assistance with any issues not covered in this manual, please contact EVIL ENERGY customer service through their official website or the retailer where the product was purchased. Please have your model number (KT01269AN6BK-HW) and purchase details available when contacting support.