Продукт бүттүview
The SEITRON POLF02 is a portable microprocessor-controlled gas detector designed for the detection of various combustible gases, including Methane, LPG, and other hydrocarbons (CxHy). This device is equipped with a flexible probe for precise gas leak localization, a large LCD display for clear readings, and an acoustic alarm for immediate alerts. Its compact design and battery operation make it ideal for field use and quick inspections.
The image displays the Seitron POLF02 portable gas detector. The main unit is black with a grey display area. The display shows "100 ppm" and has an "AUTO RANGE" indicator. Below the display are control buttons: a green power button, two navigation buttons ('>0<' and 'H'), and three function buttons ('UNIT', 'SET', 'FUNC'). A flexible black gooseneck probe extends from the top of the main unit, ending in a sensor tip. This design allows for easy access to hard-to-reach areas for gas detection.
Негизги өзгөчөлүктөрү
- Microprocessor-controlled portable fuel detector for accurate readings.
- Large 4-digit LCD display with measurement unit (ppm) and battery level indicator.
- Acoustic alarm for immediate notification of gas presence.
- Designed for detecting various hydrocarbons, including Methane (CH4) and LPG (Liquefied Petroleum Gas).
- Includes Hold function to freeze the current reading on the display.
- Features Autozero function for baseline calibration.
- Powered by a 3.7 V, 2000 mAh Li-ion battery, offering approximately 20 hours and 30 minutes of operating time.
- Compact and robust design with IP30 protection class.
Жайгашуу
1. Таңгактан чыгаруу жана текшерүү
Carefully remove the gas detector from its packaging. Inspect the device for any visible damage. Ensure all components, including the flexible probe and USB charging cable, are present.
2. Баштапкы заряддоо
Before first use, fully charge the device. Connect the supplied USB Type B cable to the detector's charging port and plug the other end into a 5V USB charger (not included). The battery indicator on the display will show charging status. A full charge typically takes several hours.
3. Күйгүзүү
Press and hold the green power button (marked with a circle and vertical line) located on the front panel until the display illuminates. The device will perform a self-test and warm-up sequence. Allow a few moments for the sensor to stabilize before taking measurements.
Иштөө нускамалары
1. Autozero Function
Before each use, or when moving to a new environment, it is recommended to perform an Autozero calibration. Ensure the device is in a clean, gas-free atmosphere. Press the 'SET' button to activate the Autozero function. The display will indicate when the calibration is complete, setting the baseline to zero.
2. Газды аныктоо
Extend the flexible probe to the area where gas detection is required. Slowly move the sensor tip around the suspected leak source. The LCD display will show the concentration of detected gas in parts per million (ppm) or other selected units. An acoustic alarm will sound if the gas concentration exceeds a predefined threshold.
3. Бирдикти тандоо
Press the 'UNIT' button to cycle through available measurement units, if applicable. The default unit is typically ppm.
4. Hold Function
To freeze the current reading on the display, press the 'H' button. This is useful for recording peak values or readings in hard-to-view locations. Press 'H' again to resume live readings.
5. Өчүрүү
To turn off the device, press and hold the green power button until the display turns off. The device also features an auto-off function after 20 hours and 30 minutes of continuous operation to conserve battery life.
Техникалык тейлөө
1. Батареяга кам көрүү
- Дисплейде батареянын заряды аз деген индикатор пайда болгондо, батареяны кайра заряддаңыз.
- Батареянын иштөө мөөнөтүн узартуу үчүн бат-баттан батареяны толугу менен түгөтпөңүз.
- If storing the device for an extended period, ensure the battery is partially charged (around 50%) and recharge it every few months.
2. Тазалоо
Аппараттын сыртын жумшак, г менен сүртүңүзamp cloth. Do not use abrasive cleaners or solvents. Ensure no liquid enters the device openings, especially the sensor tip.
3. Sensor Protection
Handle the flexible probe and sensor tip with care. Avoid bending the probe excessively or exposing the sensor to harsh chemicals or extreme temperatures, which could damage it.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Түзмөк күйбөйт. | Батарея түгөнүп калды. | Connect the device to a 5V USB charger and allow it to charge fully. |
| Inaccurate readings or fluctuating values. | Sensor not calibrated (Autozero). Presence of background gases. | Perform Autozero calibration in a clean, gas-free environment. Move to a well-ventilated area and re-test. |
| Acoustic alarm sounds continuously. | High concentration of gas detected. | Evacuate the area if safe to do so. Investigate the source of the gas leak immediately. Ensure proper ventilation. |
| Дисплей бош же тоңуп калган. | Түзмөктүн иштебей калышы же батареянын заряды аз болушу мүмкүн. | Try recharging the battery. If the issue persists, contact customer support. |
Техникалык шарттар
| Модель номери | POLF02 |
| Электр камсыздоо | Li-ion battery 3.7 V, 2000 mAh |
| Operating Time / Auto-off | Болжол менен 20 саат 30 мүнөт |
| Дисплей | 4 орундуу LCD дисплей |
| Power Connection | USB Type B socket (for charging) |
| Табылуучу газдар | Methane (CH4), LPG (Liquefied Petroleum Gas), CxHy (Hydrocarbons) |
| Өлчөмдөрү (H x W x D) | 151 мм x 72 мм x 37 мм |
| Салмагы | 640 грамм |
| Коргоо классы | IP30 |
| Заряддоочу тtage | 5 V |
Кепилдик жана колдоо
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or visit the official SEITRON webсайт. Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.
Note: This manual provides general instructions. Specific operational details may vary. Always follow local safety regulations and guidelines when using gas detection equipment.
