Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your BESTTEN Motion Sensor Light Switch, Model YM2108. This device utilizes Passive Infrared (PIR) technology to detect motion, automatically controlling lighting based on occupancy or vacancy in a room. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Сүрөт: Бүттүview of the BESTTEN Motion Sensor Switch highlighting its main features: Advanced PIR Technology, Occupancy/Vacancy Modes, compatibility with 300W LED / 800W Incandescent/Fluorescent, adjustable settings, neutral wire requirement, included wall plate, and single-pole wiring.
Коопсуздук маалыматы
ЭСКЕРТҮҮ: Risk of Electric Shock. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker before installing or servicing this switch. If you are unsure about any part of these instructions, consult a qualified electrician.
- Орнотуудан мурун автоматтык өчүргүчтүн кубаты ӨЧҮК экенин текшериңиз.
- This device requires a neutral wire for operation. Verify its presence in your wall box before purchase and installation.
- Бардык улуттук жана жергиликтүү электрдик кодекстерге ылайык орнотуңуз.
- Do not use with loads exceeding the specified ratings (120V 300W LED, 120V 800W Incandescent, 800W/VA @ 120V Rapid Start Fluorescent, 1200W/VA @ 277V Rapid Start Fluorescent).
- Үй ичинде гана колдонуу үчүн.
Продукт өзгөчөлүктөрү
- Advanced Passive Infrared (PIR) technology for motion detection.
- Supports two operating modes:
- Occupancy Mode (OS): Automatic ON, Automatic OFF.
- Vacancy Mode (VS): Manual ON, Automatic OFF.
- 180-degree motion sensor coverage.
- Adjustable sensor sensitivity.
- Adjustable time delay settings: 15 seconds (Test), 1 minute, 5 minutes, 15 minutes, 30 minutes.
- Adjustable ambient light level detection.
- Requires a neutral wire for installation.
- Single-pole wiring.
- Compatible with 120V/277VAC, 60Hz, 1/6 HP.
- UL коопсуздук үчүн тизмеленген.
- Wall plate included.
Пакеттин мазмуну
Пакетке төмөнкүлөр кирет:
- BESTTEN Motion Sensor Light Switch (Model YM2108)
- Дубал плитасы
- Орнотуу бурамалар
- Көрсөтмө (бул документ)
Орнотуу
Орнотууга чейинки текшерүү тизмеси:
- Электр кубатын өчүрүү: Locate the circuit breaker controlling the light switch and turn it OFF. Verify power is off using a voltage сыноочу.
- Нейтралдуу зым: This switch requires a neutral wire. Confirm its presence in your wall box. A neutral wire is typically white and connected to other white wires, not connected to your existing standard switch.
- Керектүү куралдар: Отвертка, зым сыргычтар, электр лентасы, томtage сыноочу.
Электр зымдары боюнча көрсөтмө:
Follow the wiring diagram below. Ensure all connections are secure.
Сүрөт: Detailed wiring diagram for the BESTTEN Motion Sensor Switch. It shows connections for Ground (green wire), Neutral (white wire), Hot (black wire), and Load (red wire). Instructions for identifying each wire are provided.
- ЖЕР: Connect the green wire from the sensor switch to the existing bare copper or green ground wire in the wall box.
- Нейтралдуу: Connect the white wire from the sensor switch to the existing neutral wire in the wall box.
- Ё: Identify the hot wire (power from the breaker panel), usually black. Connect it to the black wire on the sensor switch.
- ЖҮК: Identify the load wire (delivers power to the light fixture), usually another black wire. Connect it to the red wire on the sensor switch.
After wiring, carefully push the switch into the wall box, attach the wall plate, and restore power at the circuit breaker. For the sensor to operate, the ON/OFF switch MUST be manually pushed once after installation or a power outage.
Иштөө нускамалары
The BESTTEN Motion Sensor Light Switch offers two primary operating modes: Occupancy Mode (OS) and Vacancy Mode (VS). The mode is selected by a small switch located on the front of the device, usually labeled OS/VS.
Сүрөт: Фронт view of the BESTTEN Motion Sensor Switch illustrating the Vacancy and Occupancy mode selector, along with the Time Delay, Sensor Sensitivity, and Ambient Light Level adjustment knobs.
Occupancy Mode (OS)
In Occupancy Mode, the light will turn ON automatically when motion is detected and turn OFF automatically after a set period of inactivity. This mode is ideal for high-traffic areas where hands-free operation is desired.
- To activate: Push the OS/VS button so that 'OS' is selected (or the button is pressed in).
- Function: Automatic ON, Automatic OFF.
Vacancy Mode (VS)
In Vacancy Mode, the light must be turned ON manually by pressing the switch button. It will then turn OFF automatically after a set period of inactivity. This mode is suitable for areas where manual control over initial light activation is preferred, while still benefiting from automatic shut-off.
- To activate: Push the OS/VS button so that 'VS' is selected (or the button is released).
- Function: Manual ON, Automatic OFF.
Тарам жана Жөндөөлөр
The sensor switch features three adjustable knobs to customize its behavior:
- Убакытты кечиктирүү баскычы: Adjusts the duration the light remains ON after the last detected motion.
- Settings: 15 seconds (Test), 1 minute, 5 minutes, 15 minutes, 30 minutes.
- Use the 'Test' setting for initial setup to quickly verify motion detection.
- Сенсордук сезгичтик диапазонунун баскычы: Controls the detection range of the PIR sensor.
- Adjust from 1 (lowest sensitivity/shortest range) to 5 (highest sensitivity/longest range).
- Higher sensitivity may lead to detection of minor movements or movements outside the desired area.
- Айланадагы жарык деңгээли баскычы: Determines the ambient light level at which the sensor will activate the lights.
- Adjust from 1 (activates in brighter conditions) to 5 (activates only in very dark conditions).
- This prevents lights from turning on unnecessarily when there is sufficient natural light.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Жарык күйбөйт. |
|
|
| Light turns ON unexpectedly or stays ON too long. |
|
|
| Light flickers or does not work with certain bulbs. |
|
|
Техникалык шарттар
| Модель номери | YM2108 |
| Тtage | 120V/277VAC, 60Hz |
| Load Type & Wattage |
|
| Мотор жүк | 1 / 6 HP |
| Зымдар | Single-Pole, Neutral Wire Required |
| Сенсор түрү | Пассивдүү инфракызыл (PIR) |
| Detection Angle | 180 градус |
| Материал | Термопластикалык |
| Өлчөмдөрү (H x W x D) | 11.5 см x 6.98 см x 4.39 см (4.53 дюйм x 2.75 дюйм x 1.73 дюйм) |
| Сертификаттар | UL тизмеленген |
| Иштөө температурасы | 60°C (140°F) чейин |
Сүрөт: Diagram showing the precise dimensions of the BESTTEN Motion Sensor Switch and its included wall plate in both inches and centimeters.
Техникалык тейлөө
The BESTTEN Motion Sensor Light Switch is designed for maintenance-free operation. To clean the device, gently wipe the surface with a soft, damp кездеме. Абразивдүү тазалагычтарды же эриткичтерди колдонбоңуз. Тазалоодон мурун электр кубаты өчүрүлгөнүн текшериңиз.
There are no user-serviceable parts inside the switch. Any attempt to open or modify the device will void the warranty and could pose a safety hazard.
Кепилдик жана колдоо
This BESTTEN Motion Sensor Light Switch (Model YM2108) comes with a 3 жылдык кепилдик from the date of purchase, covering defects in materials and workmanship under normal use. This warranty does not cover damage caused by improper installation, misuse, abuse, or unauthorized modifications.
For technical support, warranty claims, or further assistance, please contact BESTTEN customer service. Refer to the product packaging or the BESTTEN official webучурдагы байланыш маалыматы үчүн сайт.
