Everbilt 1/2 HP үчүн сууга чөктүрүлүүчү алюминий соргуч насосу, туташтырылган өчүргүч менен колдонуучунун колдонмосу

Introduction

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Everbilt 1/2 HP Submersible Aluminum Sump Pump. Please read all instructions carefully before use to ensure proper function and to prevent injury or damage.

Коопсуздук маалыматы

ЭСКЕРТҮҮ: Always disconnect power before servicing or performing any maintenance on the pump.

КОРКУНУЧ: Электр шок коркунучу. Бул насос жерге туташтыруучу өткөргүч жана жерге туташтыруучу түрдөгү тиркеме сайгычы менен жабдылган. Электр тогуна урунуу коркунучун азайтуу үчүн, ал туура жерге туташтырылган, жерге туташтыргыч тибиндеги розеткага гана туташтырылганын текшериңиз.

• Электр шнур же сайгыч бузулуп калса, насосту иштетпеңиз.
• Насостун туруктуу, тегиз жерге коюлганын текшериңиз.
• Do not pump flammable or corrosive liquids.
• Балдарды жана үй жаныбарларын иштеп жаткан соргучтан алыс кармаңыз.
• Wear appropriate personal protective equipment (PPE) when handling the pump.
• This pump is designed for clear water only.

Продукт бүттүview

The Everbilt 1/2 HP Submersible Sump Pump is designed for efficient water removal from sump basins. It features an aluminum motor housing for effective cooling and a tethered float switch for automatic operation.

1-сүрөт: Everbilt 1/2 HP Submersible Aluminum Sump Pump. This image shows the black pump unit with its tethered float switch, power cord, and 1-1/2 inch FNPT discharge port. The Everbilt logo is visible on the side of the pump body.

Негизги өзгөчөлүктөрү:

• Aluminum motor housing for efficient motor cooling.
• Continuous duty, efficient 115-Volt PSC motor for lower carbon footprint; higher efficiency using less energy to operate.
• 8.25 ft. cord length.
• Submersible for quiet operation.
• 1-1/2 in. FNPT discharge.
• Semi-open thermoplastic impeller passes 3/8 in. solids.
• Ашыкча жүктөрдү жылуулуктан коргоо.

Орнотуу жана орнотуу

1. Сумп Бasin Даярдоо: Ensure your sump basin has a minimum diameter of 18 inches to accommodate the tethered float switch. Clean the basin of any debris or obstructions.
2. Жайгашкан жери: Насосту суу куюучу жайдын түбүндөгү катуу, тегиз жерге коюңуз.asin. Ensure the pump is stable and will not tip over during operation.
3. Агызуучу түтүктү туташтыруу: Connect a 1-1/2 inch FNPT (Female National Pipe Thread) discharge pipe to the pump's outlet. It is recommended to use a check valve in the discharge line to prevent water from flowing back into the sump basin насос өчүрүлгөндө.
4. Калкып жүрүүчү которгучту жөндөө: The tethered float switch controls the pump's on/off cycles. Adjust the tether length to set the desired "on" and "off" water levels. Ensure the float can move freely without obstruction within the sump basin. The switch-on height is approximately 11.81 inches and switch-off height is approximately 3.94 inches, but can be adjusted by tether length.
5. Кубат туташуу: Plug the pump's 8.25 ft. power cord into a properly grounded 115-Volt AC outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety.
6. Сыноо операциясы: Fill the sump basin with water to activate the float switch and ensure the pump turns on and discharges water correctly. Allow the water level to drop to verify the pump turns off automatically.

Иштөө нускамалары

The Everbilt 1/2 HP Submersible Sump Pump operates automatically via its tethered float switch. Once properly installed and connected to power, the pump will activate when the water level rises to the "on" point and deactivate when the water level drops to the "off" point.

• Автоматтык иштетүү: The pump is designed for continuous duty and will cycle on and off as needed based on the water level in the sump basin.
• Кол менен жокко чыгаруу (эгер бар болсо): While primarily automatic, some installations may allow for manual operation by lifting the float switch. Refer to your specific setup for manual control options.
• Мониторинг: Сумпа bны мезгил-мезгили менен текшерип туруңузasin and pump operation, especially during heavy rainfall, to ensure it is functioning correctly.

Техникалык тейлөө

Regular maintenance ensures the longevity and reliable operation of your sump pump.

1. Кубатты өчүрүү: Кандайдыр бир оңдоо иштерин жүргүзүүдөн мурун насосту дайыма электр булагынан ажыратыңыз.
2. Clean Sump Basin: Periodically remove any debris, dirt, or sediment from the sump basin that could interfere with pump operation or float switch movement.
3. Импеллерди текшерүү: Check the pump's impeller for any clogs or damage. The semi-open thermoplastic impeller is designed to pass 3/8 inch solids, but larger debris can cause issues.
4. Check Float Switch: Ensure the tethered float switch moves freely and is not obstructed by wires, pipes, or debris.
5. Электр кабелин текшерүү: Examine the power cord for any signs of wear, cuts, or damage. Replace if necessary.
6. Кышка даярдоо (эгер бар болсо): Эгерде насос нөл температурага дуушар болгон аймакта болсо жана колдонулбай турган болсо, аны бasin, clean it, and store it in a dry, warm place.

Проблемаларды чечүү

If problems persist after attempting these solutions, please contact Everbilt customer support.

Техникалык шарттар

Кепилдик жана колдоо

For warranty information or technical support, please contact Everbilt customer service. Keep your purchase receipt as proof of purchase for any warranty claims.

Кошумча жардам алуу үчүн, сиз иш сапары менен болот Everbilt brand page on Amazon or consult the retailer where the product was purchased.