WORKPRO W003068A 70-Piece 1/4-дюймдук Drive Socket Set Instruction Manual

Introduction

This manual provides instructions for the safe and effective use of your WORKPRO W003068A 70-Piece 1/4-inch Drive Socket Set. This comprehensive set includes a quick-release ratchet, a variety of metric and SAE sockets, nut bits, and screwdriver bits, designed for general auto repair and household maintenance tasks. Please read this manual thoroughly before using the tools.

1-сүрөт: Бүттүview of the WORKPRO 70-Piece 1/4-inch Drive Socket Set, showing the storage case and all included tools.

Коопсуздук маалыматы

Кол менен жасалган шаймандарды колдонууда ар дайым төмөнкү коопсуздук чараларын сактаңыз:

• Учуучу сыныктардан коргонуу үчүн коопсуздук көз айнеги сыяктуу тиешелүү жеке коргонуу каражаттарын тагыныңыз.
• Ensure the correct size and type of socket or bit is used for the fastener to prevent damage to the tool or fastener.
• Do not use excessive force. If a fastener is difficult to turn, inspect for rust, cross-threading, or other issues.
• Ишенимдүү кармоо үчүн шаймандарды таза жана майлуу эмес жерде кармаңыз.
• Store tools in their designated case to prevent loss and damage.
• This tool set is not applicable for impact drivers. Use with impact drivers can cause damage to the tools and potential injury.
• Балдар жетпеген жерде сактаңыз.

Пакеттин мазмуну

Your WORKPRO W003068A 70-Piece 1/4-inch Drive Socket Set includes the following components:

• 20-piece 1/4-inch Drive Regular Sockets:
  • SAE Sizes: 5/32'', 3/16'', 7/32'', 1/4'', 9/32'', 5/16'', 11/32'', 3/8'', 7/16'', 1/2''
  • Metric Sizes: 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13 mm
• 12-piece 1/4-inch Drive Deep Sockets:
  • SAE Sizes: 1/4'', 9/32'', 5/16'', 11/32'', 3/8'', 7/16''
  • Metric Sizes: 6, 7, 8, 9, 10, 11 mm
• 12-piece Nut Bits:
  • SAE Sizes: 1/4'', 9/32'', 5/16'', 11/32'', 3/8'', 7/16''
  • Metric Sizes: 6, 7, 8, 9, 10, 11 mm
• 20-piece Screwdriver Bits
• 1-piece 1/4-inch Reversible Ratchet
• 1-piece 1/4-inch Spinner Handle
• 1-piece 1/4-inch Universal Jointer
• 1-piece 1/4-inch Drive Extension Bar (3-inch)
• 1-piece 1/4-inch Drive Extension Bar (6-inch)
• 1-piece 1/4-inch Bit Holder
• Туруктуу сактоочу куту

2-сүрөт: Деталдаштырылган view of the regular and deep sockets included in the set, showing both Metric and SAE measurements.

3-сүрөт: Illustration of the nut bits and 20-piece screwdriver bits.

Жайгашуу

The WORKPRO W003068A socket set comes pre-organized in a durable storage case. To begin using your tools:

1. Open the latches on the storage case and lift the lid.
2. Familiarize yourself with the layout of the tools. Each socket, bit, and accessory has a dedicated slot for easy identification and organization.
3. Identify the appropriate socket or bit size (Metric or SAE) required for your task.

4-сүрөт: The organized storage case with clear recognition and dedicated slots for each tool.

Иштөө нускамалары

Using the 1/4-inch Reversible Ratchet

The reversible ratchet features a quick-release mechanism for efficient socket changes and a directional switch for tightening or loosening fasteners.

1. Розетканы туташтыруу: Press the quick-release button on the ratchet head, align the square drive of the socket with the ratchet's drive, and push the socket firmly onto the drive until it clicks into place. Release the button.
2. Removing a Socket: Press the quick-release button and pull the socket off the drive.
3. Багытын өзгөртүү: Use the lever on the ratchet head to switch between tightening (clockwise) and loosening (counter-clockwise) operations.
4. Операция: Place the socket onto the fastener. Turn the ratchet handle in the desired direction. The internal mechanism allows the handle to swing back without turning the fastener, enabling continuous operation in confined spaces.

5-сүрөт: The 1/4-inch reversible ratchet, highlighting its quick-release mechanism and directional switch.

6-сүрөт: Example of using the 1/4-inch reversible ratchet in an automotive application.

Using Extension Bars and Universal Jointer

Extension bars and the universal jointer provide access to fasteners in hard-to-reach areas.

• Extension Bars: Attach an extension bar between the ratchet and the socket to extend reach. The set includes 3-inch and 6-inch extension bars.
• Universal Jointer: The universal jointer allows the socket to pivot, providing an angled approach to fasteners that are not directly accessible. Attach it between the ratchet/extension and the socket.

7-сүрөт: The universal jointer and 3-inch and 6-inch extension bars, showing their connection points.

Using the 1/4-inch Spinner Handle and Screwdriver Bits

The spinner handle is ideal for quickly turning fasteners by hand or for tasks requiring less torque than a ratchet.

1. Розеткаларды бекитүү: Push any 1/4-inch drive socket directly onto the square drive of the spinner handle.
2. Attaching Screwdriver Bits: Insert a screwdriver bit into the 1/4-inch bit holder, then attach the bit holder to the spinner handle's square drive.
3. Операция: Grip the handle and rotate to tighten or loosen fasteners.

8-сүрөт: The 1/4-inch drive spinner handle with its dimensions.

9-сүрөт: Example of using the spinner handle with a screwdriver bit for light fastening tasks.

Техникалык тейлөө жана кам көрүү

• Тазалоо: After each use, wipe down tools with a clean, dry cloth to remove dirt, grease, and moisture. For stubborn grime, a mild degreaser can be used, followed by thorough drying.
• Даттын алдын алуу: The tools are made from chrome vanadium steel with a chrome finish for rust resistance. However, prolonged exposure to moisture can still cause corrosion. Ensure tools are completely dry before storage. A light coat of tool oil can be applied to moving parts of the ratchet for smooth operation and added protection.
• Сактагыч: Always return tools to their designated slots in the sturdy portable case. This protects the tools from damage, keeps them organized, and prevents loss. Store the case in a dry environment.
• Текшерүү: Periodically inspect tools for any signs of wear, damage, or corrosion. Replace any damaged tools to ensure safe and effective operation.

Проблемаларды чечүү

Most issues with hand tools are related to improper use or selection. Consider the following if you encounter problems:

• Socket/Bit Does Not Fit: Ensure you are using the correct size (Metric or SAE) and type of socket/bit for the fastener. Fasteners can sometimes be slightly corroded or damaged, affecting fit.
• Ratchet Slips or Does Not Engage: This may indicate wear in the ratchet mechanism. Ensure the directional lever is fully engaged. If the issue persists, the ratchet may need replacement.
• Stripping Fasteners: This usually occurs when the wrong size socket/bit is used, or excessive force is applied, especially with worn fasteners. Always ensure a snug fit before applying torque.
• Tools are Stiff or Rusty: Clean tools thoroughly and apply a light lubricant to moving parts (ratchet) or a rust preventative to surfaces.

Техникалык шарттар

Кепилдик жана колдоо

For warranty information, product support, or to inquire about replacement parts, please contact WORKPRO customer service directly. Details can typically be found on the product packaging or the official WORKPRO webсайт.

You can also visit the official WORKPRO store for more products and information: WORKPRO дүкөнү