Mad Mars 12V LED Motorcycle Scooter Turn Signals User Manual

1. Киришүү

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Mad Mars 12V LED Motorcycle Scooter Turn Signals. Please read this manual thoroughly before installation and keep it for future reference.

2. Коопсуздук маалыматы

• Электр коопсуздугу: Кыска туташуунун же электр тогуна урунуунун алдын алуу үчүн кандайдыр бир электрдик иштерди аткаруудан мурун дайыма унаанын аккумуляторун ажыратыңыз.
• Кесиптик орнотуу: If you are not familiar with motorcycle or scooter electrical systems, it is highly recommended to have these turn signals installed by a qualified professional.
• Тtage Шайкештик: These turn signals are designed for 12V DC systems only. Do not connect to higher voltage системалары.
• Коопсуз орнотуу: Ensure the turn signals are securely mounted to prevent detachment during vehicle operation.
• CE Homologation: These turn signals are CE approved, indicating compliance with European safety standards.

3. Пакеттин мазмуну

• One (1) Pair of Mad Mars 12V LED Motorcycle Scooter Turn Signals (Orange)

4. Техникалык шарттар

5. Орнотуу жана орнотуу

Туура орнотуу үчүн бул кадамдарды кылдаттык менен аткарыңыз. Кесипкөй орнотуу сунушталат.

1. Унаа даярдоо: Ensure the vehicle's ignition is off and the battery is disconnected to prevent electrical hazards.
2. Remove Old Turn Signals: Carefully remove the existing turn signals from your motorcycle or scooter. Note the wiring connections.
3. Mount New Turn Signals: Insert the threaded bolt of the Mad Mars turn signal into the mounting hole. Secure it with the provided nut, ensuring it is tight but not overtightened. The thread diameter is 8mm.

Image 1: Mad Mars 12V LED Turn Signals. This image shows a pair of orange LED turn signals with their wiring and mounting hardware.

4. Зымдарды туташтыруу:
   • Identify the positive wire of the Mad Mars turn signal (typically yellow or red) and the negative/ground wire (typically black).
   • Connect the positive wire of the turn signal to the vehicle's positive turn signal wire.
   • Connect the negative wire of the turn signal to the vehicle's negative or ground wire.
   • Use appropriate electrical connectors (not included) and ensure all connections are secure and insulated to prevent short circuits.
5. Repeat for Second Turn Signal: Follow the same steps for the other turn signal.
6. Батареяны кайра туташтыруу жана сыноо: Reconnect the vehicle's battery. Turn on the ignition and test both turn signals to ensure they flash correctly. If they do not flash or flash too quickly/slowly, you may need a load resistor or an LED flasher relay (not included).

Image 2: Mad Mars 12V LED Turn Signals (Alternate View). This image provides another view of the orange LED turn signals, highlighting their compact design.

6. Иштөө нускамалары

Once properly installed, the Mad Mars 12V LED Turn Signals operate in conjunction with your motorcycle or scooter's existing turn signal switch. Activate the left or right turn signal switch as you normally would to indicate a turn or lane change. The LED lights will flash to provide clear visibility to other road users.

7. Техникалык тейлөө

• Тазалоо: Clean the turn signal lenses periodically with a soft, damp кездеме. Пластмассага зыян келтириши мүмкүн болгон абразивдүү тазалоочу каражаттардан же эриткичтерден алыс болуңуз.
• Текшерүү: Regularly check the mounting bolts for tightness and inspect the wiring for any signs of wear, fraying, or corrosion. Ensure the connections remain secure.
• LED Узак мөөнөттүү: LED lights have a long lifespan and typically do not require replacement under normal operating conditions.

8. Кыйынчылыктарды

• Turn Signals Not Lighting Up:
  • Check all wiring connections for proper contact and insulation.
  • Verify that the vehicle's battery is charged and providing 12V power.
  • Inspect the vehicle's turn signal fuse.
• Turn Signals Flashing Too Fast (Hyper-flashing):
  • LED turn signals draw less power than traditional incandescent bulbs, which can cause the vehicle's flasher relay to interpret a bulb outage, resulting in hyper-flashing.
  • This can typically be resolved by installing a load resistor (not included) in parallel with each LED turn signal or by replacing the stock flasher relay with an LED-compatible flasher relay (not included).
• Turn Signals Not Flashing (Solid On):
  • This can also be caused by incompatibility with the vehicle's flasher relay. Consider installing a load resistor or an LED-compatible flasher relay.

9. Кепилдик жана колдоо

Кепилдик жөнүндө маалымат же техникалык колдоо алуу үчүн, сатып алуу документтерин караңыз же сатуучуга түз кайрылыңыз. Кепилдик боюнча дооматтар үчүн сатып алууну тастыктаган документти сактап коюңуз.