Robus SBM-001 Stabilizing Base for Monopods User Manual

Introduction

The Robus SBM-001 Stabilizing Base is designed to enhance the stability of monopods equipped with a 3/8"-16 threaded socket. This base features three folding legs that provide a stable platform for photography and videography, improving control and reducing camera shake. Its integrated ball joint allows for flexible camera positioning, while the friction control and locking mechanism ensure secure operation with various camera and lens combinations. The compact and lightweight design makes it highly portable.

Негизги өзгөчөлүктөрү

• Designed for monopods with a 3/8"-16 socket thread.
• Significantly adds stability to monopods.
• Folding legs for convenient transport and rapid deployment.
• Integrated locking ball-joint for flexible camera positioning.
• Friction control to adjust flexibility based on camera weight.
• Non-slip rubber feet for enhanced traction on various surfaces.

Шайкештик

The SBM-001 is compatible with:

• Robus RCM-633 6-Section Carbon Fiber Monopod
• Robus RCM-439 4-Section Carbon Fiber Monopod
• Any monopod featuring a standard 3/8"-16 threaded mounting post.

Жайгашуу

1. Attaching to Monopod: Locate the 3/8"-16 threaded socket at the bottom of your monopod. Screw the Robus SBM-001 Stabilizing Base into this socket until it is securely fastened.
2. Буттарды жайылтуу: To deploy the legs, press the release button located on each leg. The legs will spring open and lock into their extended position. Ensure all three legs are fully extended and locked before use to provide maximum stability.

Image: The Robus SBM-001 Stabilizing Base securely attached to a monopod, demonstrating its integrated use with camera equipment.

Иштөө нускамалары

1. Using the Ball Joint: The integrated ball joint allows for smooth swiveling and tilting of your camera without compromising the monopod's stability. Gently adjust the camera to your desired angle.
2. Ball Joint Lock: To prevent the monopod from tilting under heavy loads or to fix it in a specific position for enhanced control, tighten the ball joint lock. This provides a rigid setup.
3. Friction Control: The ball joint features friction control, allowing you to adjust the base's flexibility. Rotate the friction control knob to increase or decrease resistance, tailoring it to the weight of your camera and lens combination for optimal movement and stability.
4. Folding the Legs: When ready for transport, press the release button on each leg again. The legs will fold up compactly along the monopod, adding minimal length to your setup. For storage, the base can be removed from the monopod, and the legs fold to a compact 6.3 inches.

Сүрөт: каптал view of the SBM-001 base with its three legs fully deployed, ready for use.

Image: The SBM-001 base with its legs folded upwards, illustrating its compact form for easy storage and transport.

Техникалык тейлөө

To ensure the longevity and optimal performance of your Robus SBM-001 Stabilizing Base, follow these maintenance guidelines:

• Тазалоо: Wipe the base with a soft, dry cloth after each use to remove dust and debris. For stubborn dirt, a slightly damp кездемени колдонсо болот, андан кийин дароо кургатуу. Катуу химиялык заттарды же абразивдүү тазалагычтарды колдонуудан алыс болуңуз.
• Сактагыч: Store the base in a clean, dry environment when not in use. Ensure the legs are folded to prevent accidental damage.
• Текшерүү: Periodically inspect all moving parts, including the leg hinges and ball joint, for any signs of wear or damage. Ensure all screws are tight.

Проблемаларды чечүү

If you encounter issues with your SBM-001 Stabilizing Base, consider the following common solutions:

• Legs not locking: Ensure the release buttons are fully depressed when deploying the legs. Check for any obstructions in the hinge mechanism.
• Монопод туруксуз сезилет: Verify that the base is securely screwed into the monopod's 3/8"-16 socket. Ensure all three legs are fully extended and locked. Check that the ball joint lock is tightened if a fixed position is desired.
• Ball joint too loose/tight: Adjust the friction control knob on the ball joint to achieve the desired resistance for your camera setup.

Техникалык шарттар

Кепилдик жана колдоо

For information regarding warranty coverage, technical support, or service inquiries for your Robus SBM-001 Stabilizing Base, please refer to the official Robus webсайтка же кардарларды тейлөө бөлүмүнө кайрылыңыз. Сатып алуу квитанциясын кепилдик дооматтары үчүн сатып алуунун далили катары сактаңыз.