1. Продукт бүтүп калдыview
The Theben Syn 160 E is a compact analog time switch designed for DIN rail mounting. It features a single channel with a 24-hour daily program, allowing for precise control of electrical circuits based on time. This device is ideal for applications requiring automated on/off switching cycles.
Сүрөт 1: Алдыңкы view of the Theben Syn 160 E Analog Time Switch, showing the dial and manual override switch.
Негизги өзгөчөлүктөрү:
- Single channel for time-controlled switching.
- 24-hour daily program with 15-minute minimum switching time.
- Designed for DIN rail mounting (1 TE width).
- Manual override function for temporary switching.
- Potential-free switching contact.
- Quartz controlled for high accuracy.
- IP20 коргоо рейтинги.
2. Коопсуздук маалыматы
Please read these safety instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Орнотуу жана техникалык тейлөө иштери квалификациялуу электрик тарабынан гана аткарылышы керек.
- Disconnect power supply before any installation, wiring, or maintenance work.
- Ensure the device is installed in a dry environment, protected from moisture and direct sunlight.
- Do not exceed the specified maximum load current (16 A at 250 V AC).
- Verify all connections are secure and correct before restoring power.
- Аппарат үй ичинде колдонуу үчүн гана иштелип чыккан.
3. Пакеттин мазмуну
Пакет, адатта, төмөнкүлөрдү камтыйт:
- 1 x Theben Syn 160 E Analog Time Switch
- 1 х Инструкция (бул документ)
4. Орнотуу
4.1 Монтаждоо
The Theben Syn 160 E is designed for mounting on a 35mm DIN rail in an electrical distribution board or suitable enclosure. It occupies 1 module unit (1 TE) of space.
- Ensure the main power supply to the circuit is disconnected.
- Hook the top edge of the time switch onto the DIN rail.
- Press the bottom part of the time switch firmly until it clicks into place on the DIN rail.
4.2 Электр өткөргүч схемасы
Refer to the wiring diagram below for correct electrical connections. The device features potential-free switching contacts.
Figure 2: Wiring diagram for the Theben Syn 160 E. Connect the load to terminals 1 and 2 (potential-free contact), and the power supply to L and N.
- Connect the phase (L) and neutral (N) wires of the 230V AC, 50Hz power supply to the corresponding terminals on the time switch.
- Connect the load (e.g., light, fan) to the potential-free switching contacts (terminals 1 and 2). Terminal 1 is the common contact, and terminal 2 is the normally open contact.
- Бардык байланыштар бекем жана коопсуз экендигин текшериңиз.
- After wiring, close the distribution board cover and restore power.
5. Иштөө нускамалары
5.1 Учурдагы убакытты орнотуу
Rotate the time dial clockwise until the current time aligns with the time marker (usually a small arrow or line) on the housing.
5.2 Programming the Daily Schedule
The time switch features a 24-hour dial with segments, each representing 15 minutes. To program the schedule:
- To set an ON period: Push the corresponding segments on the outer ring of the dial inwards. Each pushed-in segment represents 15 minutes of the ON state.
- To set an OFF period: Leave the corresponding segments on the outer ring of the dial outwards. Each outward segment represents 15 minutes of the OFF state.
- Ensure that the desired ON/OFF times are clearly set by pushing in or pulling out the segments.
5.3 Кол менен жокко чыгаруу
The Syn 160 E includes a manual override switch, typically located on the front panel. This allows you to temporarily change the switching state regardless of the programmed schedule.
- "ON" position: The connected load will remain ON continuously.
- "OFF" position: The connected load will remain OFF continuously.
- "AUTO" (or clock symbol) position: The time switch will operate according to the programmed daily schedule.
After using the manual override, remember to return the switch to the "AUTO" position for automatic operation.
6. Техникалык тейлөө
The Theben Syn 160 E is designed for long-term, maintenance-free operation. However, general care can help ensure its longevity:
- Before cleaning, disconnect the power supply to the device.
- Clean the exterior of the device with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture.
- Ensure that no dust or debris accumulates around the ventilation openings (if any) to prevent overheating.
- Regularly check electrical connections for tightness, especially after initial installation or if the device has been moved.
7. Кыйынчылыктарды
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Device not switching ON/OFF as programmed. |
|
|
| Load remains continuously ON or OFF. |
|
|
| Device is completely unresponsive. |
|
|
8. Техникалык шарттар
| Параметр | Нарк |
|---|---|
| Модел | Syn 160 E |
| Бренд | Тебен |
| Каналдардын саны | 1 |
| Программанын түрү | Daily Program (24-hour) |
| Minimum Switching Time | 15 мүнөт |
| Supply Voltage | 230 В AC |
| Жыштык | 50 Гц |
| Power Reserve | Жок |
| Accuracy per Day | ±1 секунд |
| Switching Contact Type | Potential-free, Normally Closed (NC) |
| Rated Switching Current | 16 А 250 В AC |
| Монтаж түрү | DIN рельси (1 TE туурасы) |
| Коргоо рейтинги | IP20 |
| Өлчөмдөрү (W x Y x D) | 17.5 мм x 90 мм x 60 мм |
| Салмагы | 90 г |
Figure 3: Dimensional drawing of the Theben Syn 160 E, showing width, height, and depth measurements in millimeters.
9. Кепилдик жана колдоо
Theben products are manufactured to high quality standards. For information regarding warranty terms and conditions, please refer to the official Theben webсайтка кайрылыңыз же жергиликтүү дистрибьютериңиз менен байланышыңыз.
For technical support, troubleshooting assistance, or spare parts inquiries, please contact Theben customer service or your authorized dealer. When contacting support, please have your product model (Syn 160 E) and purchase details available.
Official Theben Webсайт: www.theben.de
