1. Маанилүү коопсуздук нускамалары
Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury when operating power tools. Read all instructions before operating this band saw.
- Көздү коргоону кийүү: Always wear safety glasses or a face shield.
- Угууну коргоону колдонуңуз: Узакка созулган ызы-чуу угууга зыян келтириши мүмкүн.
- Жумуш аймагын таза кармоо: Башаламан жерлер кырсыкка чакырат.
- Do Not Operate in Dangerous Environments: г-да электр куралдарын колдонбоңузamp же нымдуу жерлерде, же аларды жамгырга дуушар кылуу.
- Балдарды алыс кармаңыз: Бардык зыяратчылар жумуш аймагынан коопсуз аралыкта кармалышы керек.
- Коопсуз жумуш бөлүгү: Ар дайым clamp же кесүү учурунда кыймылга жол бербөө үчүн даярдалган тетикти башка жол менен бекитиңиз.
- Кокусунан баштоодон сактаныңыз: Аспапты розеткага кошуудан мурун которгучтун OFF абалында экенин текшериңиз.
- Do Not Force Tool: The tool will do the job better and safer at the rate for which it was designed.
- Куралдарды этияттык менен сактоо: Мыкты жана коопсуз аткаруу үчүн шаймандарды курч жана таза кармаңыз. Аксессуарларды майлоо жана алмаштыруу боюнча нускамаларды аткарыңыз.
- Кубатты өчүрүү: Always disconnect the band saw from the power source before making adjustments, changing accessories, or performing maintenance.
2. Орнотуу жана чогултуу
2.1 Attaching Band Saw to the Optional Stand
ЭСКЕРТҮҮ: The band saw is very heavy. Use a helper when attaching the saw to the stand.
Attach the band saw to the optional stand using the four holes provided (two are shown at (A) Fig. 7). Place one 5/16-18 x 1-3/4" hex head screw with one 5/16" flat washer through each hole through the bottom of the band saw and the top of the stand, and attach with a 5/16" lock washer, and 5/16-18 hex nut.
ЭСКЕРТҮҮ: Screws, washers, and nuts for attaching the saw to the stand come with the optional stand.
7-сүрөт: This image shows the base of the band saw with two mounting holes labeled 'A'. These holes are used to secure the band saw to an optional stand. The overall image displays the top-left portion of the original instruction page.
2.2 Attaching Motor Pulley
Both the motor pulley (A) Fig. 8, and the gearbox pulley (B) are four-step pulleys and should always be attached inverted to each other. Check to see if the gear box pulley (B) is attached with the largest step of the pulley in the "in" or "out" position. In this case, the largest step of the gear box pulley (B) is in the "in" position. Attach the motor pulley (A) to the motor shaft with the largest step of the motor pulley in the "out" position.
ЭСКЕРТҮҮ: When attaching the motor pulley (A) to the motor shaft, use the supplied 3/4" to 5/8" reducing bushing on the motor shaft. Place the supplied key in the motor shaft. Position the reducing bushing on the shaft, being sure to line the split in the reducer with the key. Position the pulley on the shaft. Line it up with the key. Secure with the two supplied 5/16-18 x 5/16" set screws.
8-сүрөт: This image illustrates the motor pulley (A) and gearbox pulley (B) arrangement. The motor pulley is shown attached to the motor shaft. This corresponds to the top-middle portion of the original instruction page.
9-сүрөт: This image provides a closer look at the motor pulley (A), gearbox pulley (B), drive pulley (C), motor mounting bars (D), and posts (E). These components are crucial for belt alignment and tensioning. This corresponds to the top-right portion of the original instruction page.
2.3 Attaching Belt and Pulley Guard, Attaching and Aligning V-Belt, Adjusting Belt Tension
ЭСКЕРТҮҮ: МАШИНАНЫ кубат булагынан АЖЫРАТ.
- Use a straight edge to align the inside grooves of the pulleys (A) and (B) Fig. 9 to the inside edge of the drive pulley (C). The pulleys can be moved in or out on the shafts and the motor can also be moved.
- Place the belt and pulley guard (A) Fig. 10A over the belt opening and position the two clamps (B) over the guard flanges and under the top of the stand. Use the four 1/4-20 x 1/2" round head screws in the holes in the bottom of the clamps to fasten in place.
- Attach the largest V-Belt to the inside groove of the motor pulley (A) Fig. 9 and to the drive pulley (C) Fig. 9. Attach the smaller V-Belt to any one of the remaining three grooves of the motor pulley (A) and the corresponding groove of the gear box pulley (A). (Fig. 10B shows belts in place. Belt and pulley guard was removed for clarity.)
- Adjust the belt tension by raising or lowering the motor on the motor mounting bars (D) Fig. 9. If necessary, the motor mounting can be repositioned on the two posts (E) Fig. 9. Keep the pulleys in alignment when performing this operation. With light finger pressure, a 1" deflection in the belt at the center span of the pulleys indicates the proper tension.
Сүр 10A: This image shows the belt and pulley guard (A) placed over the belt opening, with clamps (B) positioned over the guard flanges. This corresponds to the bottom-left portion of the original instruction page.
Сүрөт 10B: This image displays the V-belts correctly installed between the motor pulley and the gearbox pulley. The guard has been removed for visual clarity of the belt placement. This corresponds to the bottom-right portion of the original instruction page.
3. Операция
3.1 Blade Selection and Installation
Select the appropriate blade for your material (wood or metal) and desired cut. Ensure the blade is installed with the teeth pointing downwards towards the table. Proper blade tension is critical for accurate cuts and blade longevity.
3.2 Adjusting Blade Guides and Thrust Bearings
Adjust the blade guides and thrust bearings to provide proper support to the blade. The guides should be set close to the blade without binding, typically with a clearance of 0.002-0.004 inches. The thrust bearing should be positioned just behind the blade, allowing it to rotate freely but preventing excessive blade deflection during cutting.
3.3 Setting Cutting Speed
This band saw features a gearbox to obtain different speeds, suitable for both wood and metal cutting. Refer to the speed chart (typically found in the full manual) to select the correct blade speed for your material. Lower speeds are generally used for metal, while higher speeds are for wood.
3.4 Кесүү
Ensure the workpiece is stable and properly supported. Turn on the band saw and allow the blade to reach full speed before beginning the cut. Feed the material into the blade smoothly and consistently, without forcing it. Use a push stick for smaller pieces to keep hands away from the blade.
4. Техникалык тейлөө
Regular maintenance ensures the longevity and safe operation of your DELTA band saw.
- Тазалоо: Regularly clean sawdust and metal chips from the machine, especially from the blade guides, wheels, and motor area. Use a vacuum or brush; never use compressed air directly on electrical components.
- Майлоо: Follow the lubricating instructions provided in the full manual. Key areas often include wheel bearings, gearbox, and blade tensioning mechanisms.
- Бычак текшерүү: Inspect the blade for dullness, cracks, or missing teeth before each use. Replace damaged blades immediately.
- Кур чыңалуу: Periodically check and adjust belt tension as described in Section 2.3 to ensure efficient power transfer and prevent slippage.
- Электр шнурларын текшерүү: Электр шнурунда кандайдыр бир бузулуу же эскирүү бар экенин текшериңиз. Керек болсо алмаштырыңыз.
5. Кыйынчылыктарды
Бул бөлүмдө сиз лента араа менен кездешүүсү мүмкүн болгон жалпы көйгөйлөрдү чечет.
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Бычак туура эмес ээрчип жатат | Incorrect blade tension; Worn tires; Misaligned wheels | Adjust blade tension; Replace worn tires; Align wheels according to full manual |
| Ашыкча термелүү | Loose components; Unbalanced wheels; Dull blade | Check all fasteners; Inspect wheels for damage; Replace or sharpen blade |
| Motor runs but blade does not move | Broken belt; Loose belt; Blade jammed | Replace belt; Adjust belt tension; Clear any obstructions from blade path |
| Poor cut quality (rough, wavy) | Dull blade; Incorrect blade tension; Improper blade guides adjustment | Replace or sharpen blade; Adjust blade tension; Adjust blade guides for proper clearance |
6. Техникалык шарттар
The DELTA 14 Inch Wood-Metal Band Saw Model 28-303 is designed for versatile cutting applications.
- Модел: 28-303
- Blade өлчөмү: 14 Inch (nominal)
- Материалдык шайкештик: Жыгач жана металл
- Ылдамдыкты көзөмөлдөө: Multi-speed gearbox for optimized cutting across various materials.
- Монтаждоо: Designed for optional stand attachment.
For detailed technical specifications, including motor horsepower, cutting capacity, and dimensions, please refer to the complete product manual or the manufacturer's official webсайт.
7. Кепилдик маалыматы
Specific warranty details for the DELTA 14 Inch Wood-Metal Band Saw Model 28-303 are typically provided with the original purchase documentation. This may include information on warranty duration, coverage, and how to make a claim.
Please retain your proof of purchase for warranty purposes. For the most current and complete warranty information, consult the official DELTA product warranty statement or contact DELTA customer support.
8. Кардарларды колдоо кызматы
Should you require assistance with your DELTA 14 Inch Wood-Metal Band Saw Model 28-303, including technical support, parts ordering, or service, please contact DELTA customer service.
Contact information (phone numbers, email, or website) can typically be found in the full product manual, on the product packaging, or on the official DELTA tools webсайт.
When contacting support, please have your model number (28-303) and serial number ready to expedite service.
