1. Киришүү
This manual provides essential information for the proper installation and maintenance of your MTP Replacement Blade Locking Bolt. This component is designed as a direct replacement part for specific Dremel Saw Max and Ultra Saw models, ensuring secure blade attachment during operation.
Шайкештик: This replacement blade locking bolt is compatible with the following Dremel models:
- Dremel Saw Max SM20
- Dremel Saw Max SM20-02
- Dremel Ultra Saw US40
Please consult your tool's original owner's manual to confirm the correct part number (2610016801) for your specific model before proceeding with installation.
2. Коопсуздук маалыматы
WARNING: Always disconnect the power tool from its power source before performing any assembly, adjustments, or maintenance. Failure to do so can result in serious personal injury.
- Орнотуу учурунда коргоочу көз айнек жана кол кап сыяктуу тиешелүү жеке коргоочу шаймандарды (ЖКК) кийиңиз.
- Ensure the replacement part is clean and free from damage before installation.
- Do not overtighten the bolt, as this can damage the threads or the tool.
- Эгерде сиз кандайдыр бир кадам боюнча күмөн санасаңыз, квалификациялуу техникке же түпнуска шаймандын тейлөө колдонмосуна кайрылыңыз.
3. Пакеттин мазмуну
Сиздин пакетиңиз төмөнкү нерсени камтышы керек:
- 1 x MTP Replacement Blade Locking Bolt (Part Number: 2610016801)
4. Орнотуу
Follow these steps to replace the blade locking bolt:
- Кубатты өчүрүү: Ensure the Dremel tool is unplugged from the power outlet.
- Эски болтту алып салуу: Locate the existing blade locking bolt on your Dremel Saw Max or Ultra Saw. Use an appropriate tool (e.g., an Allen wrench or screwdriver, depending on the bolt head) to loosen and remove the old bolt.
- Remove Blade (if necessary): If the blade is still attached, carefully remove it after the old bolt is out.
- Текшерүү аймагы: Clean any debris or dust from the blade mounting area and the bolt's threaded hole.
- Insert New Bolt: Place the new MTP Replacement Blade Locking Bolt into the designated threaded hole.
- Secure Blade (if necessary): If you removed the blade, re-insert it correctly, ensuring it is seated properly before tightening the bolt.
- Болтту бекемдеңиз: Hand-tighten the new bolt initially, then use the appropriate tool to tighten it securely. Do not overtighten. The bolt should hold the blade firmly in place without excessive force.
- Орнотууну текшерүү: Gently attempt to move the blade by hand to ensure it is securely fastened and does not wobble.
- Сыноо куралы: Reconnect the tool to power and perform a brief, unloaded test run to ensure proper function before use.
Figure 1: MTP Replacement Blade Locking Bolt. This image shows the black, hexagonal head bolt with a threaded shaft, designed to secure a saw blade.
5. Операция
Once properly installed, the MTP Replacement Blade Locking Bolt functions identically to the original part, securing the cutting blade to your Dremel Saw Max or Ultra Saw. Ensure the bolt is always tightened correctly before operating the tool to prevent blade slippage or detachment, which could lead to injury or damage.
6. Техникалык тейлөө
- Үзгүлтүксүз текшерүү: Periodically inspect the blade locking bolt for any signs of wear, damage, or corrosion.
- Тазалоо: Keep the bolt and its threads clean from sawdust and debris. A small brush or compressed air can be used.
- Тыюулугун текшерүү: Before each use, verify that the blade locking bolt is securely tightened.
- Алмаштыруу: If the bolt shows signs of stripping, bending, or significant wear, replace it immediately to maintain tool safety and performance.
7. Кыйынчылыктарды
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Blade is loose after tightening bolt. | Bolt not fully tightened, stripped threads on bolt or tool, incorrect blade seating. | Ensure bolt is tightened correctly. Inspect bolt and tool threads for damage; replace if stripped. Verify blade is seated properly. |
| Bolt cannot be removed or tightened. | Cross-threaded, seized due to corrosion, or damaged bolt head. | Apply penetrating oil if seized. Use correct tool for bolt head. If severely damaged, professional assistance may be required. |
| Bolt does not fit. | Incorrect part for your tool model. | Verify compatibility with your Dremel model (SM20, SM20-02, US40) and part number (2610016801). |
8. Техникалык шарттар
- Бөлүк түрү: Blade Locking Bolt
- Бренд: MTP
- Шайкештик: Dremel Saw Max SM20, SM20-02, Dremel Ultra Saw US40
- OEM Part Number Equivalent: 2610016801
- Баштын стили: Hexagonal (Round head with hex drive)
- Material Grade: 2-класс
- ASIN: B0B2CCTVTJ
9. Кепилдик жана колдоо
For information regarding warranty coverage or technical support for your MTP Replacement Blade Locking Bolt, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.
For support related to your Dremel tool, please refer to the official Dremel documentation or contact Dremel customer service.
