Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Cloudy Bay In-Wall Dimmer Switch, Model CBLD001WHA. This dimmer switch is designed for use with LED, CFL, and incandescent light fixtures, offering both single-pole and 3-way control options. Please read these instructions carefully before installation and retain them for future reference.
Фронт view of the Cloudy Bay In-Wall Dimmer Switch.
Коопсуздук маалыматы
- ЭСКЕРТҮҮ: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse and test that power is off before wiring.
- Бардык улуттук жана жергиликтүү электрдик кодекстерге ылайык орнотуңуз.
- Эгерде ушул көрсөтмөлөрдүн кайсы бир бөлүгүндө күмөн болсоңуз, квалификациялуу электрикке кайрылыңыз.
- Күңүртүлбөгөн жарык булактары менен колдонбоңуз.
- This dimmer is for indoor use only.
Кутуда эмне бар
Орнотууну баштоодон мурун бардык компоненттер бар экендигин текшериңиз:
- 1 x Dimmer Switch
- 1 x Screwless Cover Plate (Outer Plate)
- 1 x Inner Plate (Mounting Frame)
- 4 x зым гайкалар
- 4 x Монтаждоо бурамалар
Illustration of the dimmer switch components, including the dimmer unit, inner plate, outer plate, wire nuts, and mounting screws.
Орнотуу жана орнотуу
1-кадам: Электр кубатын өчүрүңүз
Before starting any electrical work, turn off the power at the circuit breaker or fuse box. Ensure the power is off by testing the circuit with a voltage сыноочу.
2-кадам: Учурдагы которгучту алып салуу
Carefully remove the wall plate and mounting screws from the existing switch. Gently pull the old switch out of the electrical box. Do not disconnect wires yet.
Step 3: Identify Circuit Type and Wires
Determine if your wiring is a single-pole or 3-way configuration. A single-pole circuit controls lights from one location, while a 3-way circuit controls lights from two locations.
Бир уюлдуу зымдар:
Typically involves two wires connected to the switch (Hot Input and Load) plus a ground wire. One of the red wires on the dimmer will be capped off.
Diagram illustrating single-pole wiring for the dimmer switch, showing connections for hot input, load, and ground wires.
3 тараптуу зымдар:
Involves three wires connected to the switch (Hot Input, Traveler 1, Traveler 2) plus a ground wire. The dimmer switch will replace one of the existing 3-way switches.
Diagram illustrating 3-way wiring for the dimmer switch, showing connections for hot input, two traveler wires, and ground.
Step 4: Wire Your New Dimmer
Connect the dimmer switch wires to the house wires using the provided wire nuts. Ensure all connections are secure.
- туташтыруу жашыл же жылаңач жез жер зым from the wall box to the жашыл зым диммерде.
- туташтыруу black dimmer wire -га hot input wire дубал кутучасынан.
- үчүн Бир поляк: Connect one of the red dimmer wires -га жүктөө зымы (to the light fixture). Cap off the other red dimmer wire with a wire nut.
- үчүн 3-жол: Connect the two red dimmer wires экөөнө саякат зымдары from the wall box. If the on/off direction is reversed after wiring, try switching the two red wires.
Detailed diagram showing wiring connections for both single-pole and 3-way installations, along with steps for mounting and adjusting the dimming range.
Step 5: Mount the Dimmer
Carefully push all wires into the wall box, leaving enough room to insert the dimmer. Secure the dimmer to the wall box using the provided mounting screws.
Step 6: Separate Mounting Frame from Wall Plate
Gently insert a flat-head screwdriver into the slots on the side of the wall plate to separate the inner mounting frame from the outer decorative wall plate.
Illustration demonstrating the separation of the face plate from the mounting frame.
7-кадам: Wall Plate орнотуу
Place the decorative wall plate over the installed mounting frame. Snap the outer plate onto the inner frame until it clicks securely into place.
Step 8: Adjust Dimming Range (Sensitivity Adjustment)
A trim dial located below the cover plate allows for sensitivity adjustment to optimize compatibility with various LED lamps and prevent flickering at low light levels.
- Электр өчүргүчтөн кубатту күйгүзүңүз.
- Turn the dimmer on and set the slide control to the lowest dimming level.
- Remove the outer wall plate to access the trim dial.
- Use a small screwdriver to turn the trim dial clockwise to increase the minimum brightness or counter-clockwise to decrease it. Adjust until the desired minimum light level is achieved without flickering.
- Turn the dimmer off, then back on to ensure the bulbs turn on consistently at the minimum setting.
- Once adjusted, replace the outer wall plate.
Illustration detailing the location and function of the dimming range adjustment wheel.
Иштөө нускамалары
The Cloudy Bay Dimmer Switch features a rocker switch for on/off control and a slide control for dimming.
- Рокер которуштуруу: Press the top of the rocker switch to turn lights ON. Press the bottom to turn lights OFF.
- Слайд башкаруу: Move the slider up to increase brightness and down to decrease brightness.
Illustration of the dimmer switch controls: rocker switch for on/off and slide control for brightness adjustment.
Шайкештик
This dimmer switch is compatible with the following bulb types:
- Жылытуу: Up to 600W (120V/60Hz)
- Күңүрттөөчү CFL: Up to 150W (120V/60Hz)
- Өнүгүү LED: Up to 150W (120V/60Hz)
Маанилүү эскертүүлөр:
- Do not mix bulb types on the same dimmer circuit.
- Dimmable LEDs may not dim to the same low level as incandescent or halogen bulbs. The dimming range of LEDs can vary by manufacturer. If your bulbs hum, buzz, or flicker, they may not be fully compatible with this dimmer. Refer to the 'Adjusting Dimming Range' section for optimization.
Visual representation of the dimmer's compatibility with different bulb types and associated wattage рейтинги.
Техникалык тейлөө
The dimmer switch requires minimal maintenance. To clean, gently wipe the surface with a soft, damp кездеме. Абразивдүү тазалагычтарды же эриткичтерди колдонбоңуз.
Проблемаларды чечүү
| Маселе | Чечим |
|---|---|
| Light flashes in the whole dimming range |
|
| Light flashes in low dimming range | Slightly turn the adjustment dial counter-clockwise to achieve full compatibility with the lights. Refer to 'Adjusting Dimming Range' section. |
| Башка маселелер | Obtain a dimmer compatibility list from your light bulb/lighting fixture supplier. A broader dimmer list often means less dimming issues like flicker or buzz. Consider using FCC compliant lighting products for stable performance. |
Visual representation of the troubleshooting guide, outlining common problems and their respective solutions.
Техникалык шарттар
| Өзгөчөлүк | Спецификация |
|---|---|
| Модель номери | CBLD001WHA |
| Иштөө режими | ON-DIM-OFF |
| Учурдагы рейтинг | 1.25 Amps |
| Operating Voltage | 120 вольт |
| Байланыш түрү | Адатта ачык |
| Туташтыргыч түрү | Clamp |
| Терминал | Бурама |
| Circuit Type | 3 тараптуу / Бир уюл |
| Актуатор түрү | Push Button (Rocker) |
| Максималдуу ысытуу жүк | 600 Вт |
| Max Dimmable LED/CFL жүктөө | 150 Вт |
| Өлчөмдөрү (L x W x Y) | 1.85 x 2.76 x 4.53 дюйм |
| Сертификаттар | UL тизмеленген |
Detailed dimensions of the dimmer switch, inner plate, and outer plate.
Кепилдик жана колдоо
This Cloudy Bay Dimmer Switch comes with a 1-Year Warranty. If you encounter any issues with dimming or have questions regarding the product, please contact Cloudy Bay customer support for assistance.
Көбүрөөк колдоо үчүн, кириңиз CLOUDY BAY Store or refer to the official product documentation.
