DieseRC Kinetic Wireless Light Switch and 10A Relay Receiver Kit User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your DieseRC Kinetic Wireless Light Switch and 10A Relay Receiver Kit. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.

The DieseRC Kinetic Wireless Light Switch system offers a convenient and energy-efficient solution for controlling lighting and other electrical appliances. It features a self-generating switch that requires no batteries and an RF 433 MHz relay receiver with a 10A fuse for protection.

Коопсуздук маалыматы

• Always disconnect power at the circuit breaker before installing or servicing the receiver.
• Installation should be performed by a qualified electrician or a person with sufficient electrical knowledge.
• Ensure the receiver's load does not exceed 1500W (10A at 110V-240V AC).
• The wireless switch is IPX4 waterproof, suitable for damp environments, but avoid submerging it in water.
• Түзмөктү оңдоого же өзгөртүүгө аракет кылбаңыз. Жардам алуу үчүн кардарларды колдоо кызматына кайрылыңыз.

Орнотуу жана орнотуу

1. Пакеттин мазмуну

• 1 x DieseRC Kinetic Wireless Switch
• 1 x DieseRC 10A Relay Receiver
• Монтаждык аксессуарлар (буроолор, эки тараптуу скотч)
• User Manual

2. Component Overview

The wireless switch is self-powered and measures approximately 86mm x 86mm x 11mm. The compact relay receiver measures 60mm x 43mm x 27mm and includes a learning button, indicator light, and a replaceable 10A fuse.

3. Кабылдагычтын зымдары

The receiver must be wired between the power supply (AC 110V-240V) and the appliance you wish to control. Ensure power is disconnected before wiring.

1. Identify the Live (L) and Neutral (N) wires from your power supply.
2. Connect the Live (L) wire from the power supply to the 'L INPUT' terminal on the receiver.
3. Connect the Neutral (N) wire from the power supply to the 'N INPUT' terminal on the receiver.
4. Connect the Live (L) wire of your appliance (e.g., light fixture) to the 'L OUTPUT' terminal on the receiver.
5. Connect the Neutral (N) wire of your appliance to the 'N OUTPUT' terminal on the receiver.
6. Бардык байланыштар коопсуз экенин текшериңиз.

The receiver is designed to handle a maximum load of 1500W and operates on AC 110V-240V. It includes a 10A fuse for overload protection.

4. Switch Placement

The kinetic wireless switch requires no wiring or batteries, offering flexible placement options:

• Дубалга орнотуу: Use the provided screws or double-sided tape to fix the switch to any wall surface.
• Айнек бети: The double-sided tape allows for mounting on glass.
• Портативдик колдонуу: The switch can be placed on a table or carried as a portable remote control.

Операция

1. Зымсыз коммутаторду кабыл алгыч менен жупташтыруу

To establish communication between the wireless switch and the receiver, follow these pairing steps:

1. Press and hold the learning button on the receiver for approximately 3-5 seconds. The blue indicator light on the receiver will illuminate. Release the button.
2. Within a few seconds, press one button on the kinetic wireless wall switch once.
3. The indicator light on the receiver will flash, indicating successful pairing.

Once paired, pressing the switch will toggle the connected appliance ON or OFF.

2. Clearing the Paired Signal

To clear all paired signals from the receiver (e.g., when replacing a switch or reconfiguring):

• Press and hold the learning button on the receiver for approximately 8-10 seconds.
• The indicator light will flash multiple times, confirming that all stored signals have been cleared.

3. Multi-Control Scenarios

The system supports flexible control configurations:

• Multiple Switches, One Receiver: You can pair up to 5 wireless switches with a single receiver, allowing control from various locations (e.g., top and bottom of stairs).
• One Switch, Multiple Receivers: A single wireless switch can be paired with multiple receivers to control several appliances simultaneously or in different areas.

4. Control Distance and Signal Penetration

The system utilizes RF 433 MHz radio frequency for signal transmission. A strong signal can pass through walls, floors, and doors. The typical indoor control distance is up to 50 meters. In open outdoor spaces, the control distance can extend up to 100 meters.

Техникалык тейлөө

• Тазалоо: Wipe the switch and receiver with a dry, soft cloth. Do not use abrasive cleaners or solvents.
• Сактагычты алмаштыруу: The receiver contains a replaceable 10A fuse. If the receiver stops functioning due to an overload, disconnect power, open the fuse compartment, and replace the fuse with one of the same rating (10A).
• Self-Powered Switch: The kinetic switch does not require battery replacement. Its self-generating mechanism is designed for long-term use (over 200,000 clicks).
• Реле мөөнөтү: The high-quality relay in the receiver is designed for over 400,000 operations.

Проблемаларды чечүү

Техникалык шарттар

Кепилдик маалымат

DieseRC products are manufactured to high-quality standards. Specific warranty details may vary by region and retailer. Please retain your proof of purchase for any warranty claims. For detailed warranty terms, refer to the documentation provided with your purchase or contact DieseRC customer support.

Кардарларды колдоо

If you encounter any issues or have questions regarding your DieseRC Kinetic Wireless Light Switch and 10A Relay Receiver Kit, please contact DieseRC customer support through your retailer or the official DieseRC website. Our team is dedicated to providing assistance and resolving any concerns you may have.