Introduction
This user manual provides comprehensive instructions for the Dasqua 8300-0095 Digital Measuring Compass Set. It covers setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your tools. Please read this manual carefully before using the product.
Продукт бүттүview
The Dasqua 8300-0095 set is a versatile collection of digital measuring instruments designed for precision work in various applications, including woodworking and engineering. The set includes:
- Digital Caliper (0-150mm): A precision instrument for measuring internal, external, depth, and step dimensions. Features a plastic body for lightweight handling.
- Digital Bevel Box Angle Gauge: Used for measuring and setting angles with high accuracy.
- Digital Protractor (150mm long): A tool for measuring and marking angles, often used in conjunction with a ruler.
- Digital Height Gauge: Designed for precise height measurements.
An image showing the complete Dasqua 8300-0095 Digital Measuring Compass Set, neatly organized within its blue plastic storage case. The set includes a digital caliper, a digital angle ruler, a digital protractor, and a digital height gauge, all with digital displays. A battery is also visible in the case.
Жайгашуу
- Пакеттен чыгаруу: Carefully remove all components from the plastic storage case. Inspect each tool for any signs of damage during transit.
- Батарея орнотуу:
Each digital tool in the set requires battery power. Locate the battery compartment on each device (typically on the back or side of the digital display unit). Insert the appropriate battery type (usually a button cell battery like CR2032, though specific type may vary per tool) with the correct polarity (+/-). Close the battery compartment securely.
- Баштапкы күйгүзүү: Press the "ON/OFF" button on each tool to power it on. The digital display should illuminate.
- Zeroing (Calibration):
- Digital Caliper: Close the jaws completely and press the "ZERO" button. The display should read 0.00mm or 0.00in.
- Digital Angle Ruler/Protractor: Place the tool on a flat, level surface or against a known 0-degree reference. Press the "ZERO" button.
- Digital Height Gauge: Place the base on a flat, level surface and lower the measuring probe until it touches the surface. Press the "ZERO" button.
Always zero the instrument before taking critical measurements to ensure accuracy.
Иштөө нускамалары
General Operation for Digital Tools:
- ON/OFF баскычы: Аппаратты күйгүзүү же өчүрүү үчүн басыңыз.
- ZERO баскычы: Resets the display to zero at any point, allowing for relative measurements.
- MODE/mm/inch/fraction Button: Toggles between metric (mm), imperial (inch), and sometimes fractional inch units, depending on the tool.
- INC/ABS Button (Height Gauge): Toggles between incremental (relative) and absolute measurement modes.
Specific Tool Usage:
Digital Caliper:
- External Measurement: Place the object between the main jaws.
- Internal Measurement: Use the small jaws on top to measure inside diameters.
- Тереңдикти өлчөө: Extend the depth rod from the end of the caliper into a hole or recess.
- Кадамды өлчөө: Use the step face at the end of the fixed jaw to measure steps.
Digital Angle Ruler / Protractor:
- Open the arms to the desired angle. The digital display will show the angle reading.
- Use the "HOLD" function (if available) to lock the reading.
Digital Height Gauge:
- Place the object to be measured on the same flat surface as the height gauge.
- Lower the measuring probe until it touches the top of the object. Read the measurement from the display.
Техникалык тейлөө
- Тазалоо: Wipe the tools with a clean, dry, soft cloth after each use. For stubborn dirt, a cloth lightly dampened with water or mild detergent can be used, but ensure no liquid enters the electronic components. Do not use solvents or abrasive cleaners.
- Сактагыч: Store the tools in their original plastic storage case when not in use. This protects them from dust, moisture, and physical damage. Keep them in a dry environment away from direct sunlight and extreme temperatures.
- Батареяны алмаштыруу: When the display becomes dim or erratic, it's time to replace the battery. Refer to the battery installation steps in the "Setup" section. Dispose of old batteries responsibly.
- Care for Digital Components: Avoid dropping the tools or subjecting them to strong impacts, as this can damage the sensitive electronic components and affect accuracy.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Дисплей бош же күңүрт. | Батарея аз же өлүк. | Батареяны алмаштырыңыз. Туура полярдуулукту камсыз кылыңыз. |
| Туура эмес окуулар. | Tool not zeroed correctly; dirt/debris on measuring surfaces; physical damage. | Zero the tool before use. Clean measuring surfaces. Inspect for damage; if damaged, repair or replace. |
| Баскычтар жооп бербейт. | Low battery; internal electronic issue. | Replace the battery. If issue persists, contact customer support (if available). |
Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Өндүрүүчү | Dasqua |
| Модель номери | 8300-0095 |
| Power Source | Батарея менен иштейт |
| Камтылган компоненттер | Digital Caliper, Digital Angle Gauge Protractor, Digital Protractor, Digital Height Gauge |
| Caliper Measurement Range | 0-150 мм |
| Caliper Body Material | Пластик |
Кепилдик жана колдоо
Information regarding product warranty and direct customer support for the Dasqua 8300-0095 Digital Measuring Compass Set is not available in the provided product details. Please refer to the retailer or your purchase documentation for specific warranty terms and contact information for support.
