Schwinn Coston CE гибриддик электр велосипедин колдонуучунун колдонмосу

Introduction

This manual provides essential instructions for the assembly, operation, maintenance, and troubleshooting of your Schwinn Coston CE Hybrid Electric Bike. Please read this manual thoroughly before your first ride to ensure safe and optimal performance.

Image: The Schwinn Coston CE Hybrid Electric Bike, Matte Red, showcasing its frame, wheels, and integrated battery.

Коопсуздук маалыматы

Always wear a helmet when riding your electric bike. Ensure all components are properly assembled and tightened before each ride. Regularly check tire pressure, brakes, and battery charge. This eBike complies with ANSI/CAN/UL2849 standards.

Орнотуу жана чогултуу

Your Schwinn Coston CE Hybrid Electric Bike arrives partially assembled. The following steps detail the final assembly process.

Монтаждоо үчүн керектүү аспаптар:

• 3, 4, 5, and 6 mm Hex Keys
• Flathead бурагыч
• Филлипс баш бурагычы
• Box Cutter, Cable Cutter, or Scissors
• Pedal Wrench or Adjustable Wrench

Unboxing and Initial Preparation:

1. Locate the zip strip tab at the top corner of the box. Pull the tab all the way across the box, then open the box top.
2. Carefully remove the entire bike from the box and set it on top of the box.
3. Before removing packaging, identify the wires located near the handlebars, under the bike behind the front chainring, and along the chainstay near the rear wheel.
4. Snip off the straps holding the front wheel to the bike and remove all additional packaging from the wheel.
5. Remove packaging from the rest of the bicycle, taking care not to cut any identified wires. Leave the fork spacer in for now.
6. Lift the bicycle and set the rear wheel in the box with the fork hanging over the side. Gently place the handlebar at the front of the bike.

Step 1: Install Handlebars

1. Use a 4mm hex wrench to loosen the four bolts securing the stem faceplate and remove the faceplate. Set the faceplate and bolts in a safe place.
2. Place the handlebar in the stem and verify the brake and shift cables wrap around the frame without kinks or twisting.
3. Reinstall the stem faceplate, but do not tighten the bolts yet.
4. Center the handlebar in the stem using the markings on the handlebar.
5. Rotate the handlebar to a comfortable position, with the brake levers pointing down slightly.
6. Evenly tighten the 4mm faceplate bolts in a crisscross pattern. Ensure the gap between the faceplate and stem is equal all the way around.
7. Locate three sets of color-coded wires at the front of the bike. Connect the cables from the handlebar to the corresponding colored cables at the head tube (front of the bicycle). Simply line up the arrows on the plugs and press together. The colored portion of the plugs should disappear when properly connected.
8. Slide the controller into place on the left side of the handlebar. Rotate the controller into position, then use a 3mm hex key to tighten the bolt securing the controller to the handlebar.

Step 2: Install Seatpost

1. Open the quick release lever, then slide the seatpost into the frame.
2. Ensure the seatpost is inserted past the minimum insertion line marked on the post.
3. Close the seatpost quick release lever.
4. Lift the bike out of the box and set it on the ground standing straight up.

Step 3: Install Front Fender, Light, and Wheel

Note: Not all eBikes include fenders. Refer to your owner's manual for specific model details.

1. Loosen and remove the bolt at the fork crown.
2. Pull the fender through the fork from the rear with one hand. Use your other hand to bring the front light up so its mounting tab meets up with the front fender mounting tab at the hole in the fork crown.
3. While holding the light in place with the fender tab, reinstall the bolt in the fork crown. The order should be: fork crown, light mount, fender mount, then the bolt head.
4. Align the light and fender with the fork, then tighten the bolt with a screwdriver. Adjust the front light so it points straight ahead.
5. Secure the fender straps to the middle of each fork leg. Remove the left side bolt, then place the fender strap over the bolt hole and reinstall the bolt. Tighten the bolt with a screwdriver.
6. Repeat this process on the right side of the fork.
7. Open the parts box and locate the quick release skewer. Set the pedals aside for now.
8. On the quick release, there should be an adjusting nut, two springs, and the quick release lever. Remove the adjusting nut and one spring.
9. Remove any packaging from the axle, then insert the quick release skewer through the front wheel axle from the side opposite the brake disc.
10. Reinstall the spring, narrow end first, and lightly tighten the adjusting nut. The order on the axle should be: adjusting nut, spring, wheel, the second spring, then the quick release lever.
11. With your foot, remove the fork spacer at the dropouts.
12. To install the front wheel, lift the front of the bike and roll the wheel back, ensuring the brake disc goes into the brake caliper. Then lower the fork dropouts onto the axle.
13. Slowly tighten the adjusting nut, then close the quick release lever to see if it's tight enough. If it's too loose, open the lever, tighten up the nut more, then close the quick release lever. The quick release is properly tight when it requires a lot of effort to close the lever and the lever leaves a mark on your hand.

4-кадам: Педалдарды орнотуу

Pedals are side-specific (right and left). Check the sticker on each pedal.

1. Install the right pedal, threading in the direction of the front wheel. Then use a pedal wrench or adjustable wrench to fully tighten.
2. Repeat this process on the left side. Always remember to tighten in the direction of the front wheel. Both pedals should be very tight.

Step 5: Adjustments & Safety Check

1. Rotate the front reflector so it points straight forward. Then tighten the bolt to secure it.
2. Ensure the wheel reflectors are snug by pulling them toward the rim.
3. Use a 4mm hex key to fully tighten the stem bolts in a crisscross pattern. Verify the gap between the stem and faceplate is even from top to bottom and side to side.
4. Use a hex key to evenly tighten the two bolts securing the stem to the fork.
5. Straddle the front wheel and attempt to twist the bars to make sure they don't twist.
6. Vigorously rock and twist the saddle back and forth to ensure it doesn't move while riding.
7. Open the seatpost quick release, then raise the saddle to approximately hip level. Close the quick release lever. At your correct seat height, your knee should have a slight bend in it at the bottom of the pedal stroke.
8. Check that the brakes work by rolling back and forth slightly, then squeezing the brake levers to verify the grip. Ensure the brake levers don't pull back too far. There should be a gap between the lever and grip with the brake applied.
9. Verify the front wheel quick release is tight. The lever should be hard to close, leaving a mark on the palm of your hand.
10. Inflate the tires to the manufacturer's recommended pressure, which is marked on the tire sidewall.

Step 6: Battery & Controller

1. Press the power button at the bottom of the battery pack to power on the electric drive system.
2. Next, press and hold the center ON button on the controller until the display appears.
3. Use the top PLUS button to increase the assist level, or the bottom MINUS button to decrease the level of assist.
4. The center button on the controller scrolls through the ride statistics, including time, trip distance, average speed, and maximum speed.
5. Hold the center button down for two seconds to power down the controller.
6. To charge the battery on the bike, open the charge port cover on the lower left side of the frame. You will see the charge level displayed on the LEDs near the power button on the battery.
7. To remove the battery, insert the key into the keyhole at the upper left side of the frame near the head tube. Turn the key, then press the button at the top of the battery to release it.
8. To charge the battery off the bike, insert the charging cable into the battery charge port. The charge level will appear on the LEDs near the power button.
9. To reinstall the battery, place the bottom edge of the battery into the frame. Then lift the upper portion of the battery into place. When properly installed, it will click into place.

Operating Your Schwinn Coston CE

Electric Assist and Throttle:

• The 250-watt brushless geared hub-drive pedal assist motor provides assistance up to 20 mph.
• Use the controller on the handlebar to adjust the pedal assist level (1-5).
• The throttle allows for acceleration without pedaling.

Image: The handlebar display of the Schwinn Coston CE, showing the throttle, 5 levels of pedal assistance, current speed (20.0 MPH), and average speed (17.2).

Gears and Braking:

• The 7-speed trigger shifter offers smooth gear changes for adapting to various terrains.
• Mechanical disc brakes provide reliable stopping power in all weather conditions.

Image: A person riding the Schwinn Coston CE Hybrid Electric Bike on a paved path, highlighting its suitability for commuting and leisure rides.

Lighting and Visibility:

• Integrated LED lights on the battery, head, and taillights enhance visibility during low-light conditions.

Image: The Schwinn Coston CE Hybrid Electric Bike with its integrated LED headlight and taillight illuminated, emphasizing visibility features.

Техникалык тейлөө

• Regularly check tire pressure and inflate to the recommended PSI found on the tire sidewall.
• Inspect brake levers and calipers for proper function and adjustment.
• Keep the chain clean and lubricated for smooth gear changes.
• Бардык болттордун жана бекиткичтердин бекемдигин мезгил-мезгили менен текшерип туруңуз.
• Clean the bike frame with a damp кездеме; электрдик компоненттерди түздөн-түз жогорку басым менен жуугандан алыс болуңуз.

Батареяны заряддоо

• The integrated downtube (360-watt) battery can last up to 45 miles on a single charge, depending on conditions.
• Толук кубаттоо, адатта, болжол менен 4 саатты талап кылат.
• Батареяны велосипедге орнотуп же алып салууда заряддоого болот.
• To charge on the bike: Open the charge port cover on the lower left side of the frame and insert the charging cable. The charge level will be displayed on the LEDs near the power button.
• To remove the battery for charging: Insert the key into the keyhole at the upper left side of the frame near the head tube. Turn the key, then press the button at the top of the battery to release it.
• To reinstall the battery: Place the bottom edge of the battery into the frame, then lift the upper portion into place until it clicks.

Жалпы көйгөйлөрдү чечүү

• Көрсөтүү үчүн күч жок: Ensure the battery is fully charged and properly seated in the frame. Check all cable connections at the head tube.
• Brakes Feel Spongy: Inspect brake pads for wear and cables for proper tension. Adjust as needed or consult a bike mechanic.
• Pedal Assist Not Working: Verify the controller is powered on and the assist level is set above zero. Check for any loose wire connections.
• адаттан тыш үндөр: Stop riding immediately and inspect the bike for loose components, rubbing parts, or damaged areas.

Техникалык шарттар

Image: Schwinn Coston CE Size Guide, detailing recommended rider heights for Step-Over (X/S, S/M, L/XL) and Step-Through (X/S, S/M, L/XL) frame styles.

Кепилдик маалымат

The Schwinn Coston CE Hybrid Electric Bike comes with a limited warranty. Please refer to the owner's manual included in your bike box for full details regarding warranty coverage and terms. It is recommended to read the owner's manual before your first ride.

Колдоо

For additional assistance, troubleshooting, or to contact customer support, please refer to the official Schwinn website or the contact information provided in your owner's manual. Live chat support may be available during business hours (M-F).