ZTW Mantis G2 сериясы 85A ESC колдонуучу колдонмосу

1. Киришүү

The ZTW Mantis G2 Series 85A Electronic Speed Controller (ESC) is an advanced 32-bit brushless speed controller designed for high-performance RC airplanes and fixed-wing aircraft. This ESC integrates a powerful 8A adjustable Switching BEC (SBEC) to provide stable power to your receiver and servos. It supports a wide range of battery configurations (3-8S LiPo/LiHV) and offers precise control and reliable operation for your aircraft's propulsion system.

Please read this manual thoroughly before installation and operation to ensure correct usage and maximize the performance and lifespan of your ESC.

2. Коопсуздук чаралары

Improper use of the ESC can lead to personal injury and damage to the product or associated equipment. Always observe the following safety guidelines:

• Батарея туташуу: Always connect the battery with correct polarity. Reverse polarity will cause immediate and irreversible damage to the ESC.
• Изоляция: Ensure all connections are properly insulated to prevent short circuits.
• Пропеллердин коопсуздугу: Always remove the propeller from the motor before performing any setup, testing, or maintenance to prevent accidental injury.
• Жылуулук: The ESC can generate significant heat during operation. Ensure adequate airflow for cooling and avoid touching it immediately after use.
• Суу жана ным: Keep the ESC away from water, moisture, and conductive contaminants.
• Тtage диапазону: Көрсөтүлгөн киргизүү көлөмүн ашпаңызtage range (3-8S LiPo/LiHV).
• Балдар: This product is not a toy and is not suitable for children under 18 years of age without adult supervision.

3. Продукциянын өзгөчөлүктөрү

• Advanced 32-bit microprocessor for precise control and rapid response.
• High-current capability: 85A continuous, 95A burst (10 seconds).
• Wide input voltage range: Supports 3-8S LiPo/LiHV batteries.
• Integrated 8A adjustable SBEC with selectable output voltages: 6V, 7.4V, or 8.4V.
• Designed specifically for RC airplane and fixed-wing applications.
• Multiple protection features including low-voltage cut-off, overheat protection, and throttle signal loss protection.
• Programmable via ZTW LCD Program Card G2 or dedicated Android/iOS mobile application.

4. Техникалык шарттар

5. Орнотуу жана орнотуу

Proper installation is crucial for the safe and efficient operation of your ESC. Follow these steps carefully:

1. Мотор туташуусу: Connect the three motor wires (typically labeled A, B, C or U, V, W) from the ESC to the corresponding wires on your brushless motor. The order may affect motor rotation direction; this can be adjusted later if needed.
2. Батарея туташуу: Connect the main power wires (red for positive, black for negative) from the ESC to your LiPo/LiHV battery. Ensure the connector type matches and polarity is correct.
3. Алуучу туташуусу: Plug the throttle signal cable (usually a three-wire servo connector) from the ESC into the throttle channel (typically channel 3) of your RC receiver.
4. SBEC Voltage Тандоо: The Mantis G2 85A ESC features an adjustable SBEC. Refer to the programming section or the dedicated program card/app to set the desired output voltage (6V, 7.4V, or 8.4V) for your receiver and servos. Ensure the selected voltage сиздин кабыл алгычыңыз жана серволоруңуз менен шайкеш келет.
5. Монтаждоо: Securely mount the ESC in your aircraft, ensuring good airflow for cooling. Avoid mounting it in enclosed spaces without ventilation.

6. Иштөө нускамалары

Before first flight, it is essential to perform a throttle range calibration to ensure the ESC correctly interprets your transmitter's throttle stick positions.

6.1. Throttle Range Calibration

1. Turn on your transmitter and set the throttle stick to its maximum (full throttle) position.
2. Connect the battery to the ESC. The ESC will emit a series of beeps.
3. After the initial beeps, the ESC will detect the full throttle signal and emit a confirmation tone.
4. Move the throttle stick to its minimum (zero throttle) position. The ESC will emit another series of beeps, indicating the throttle range has been successfully calibrated.
5. The ESC is now ready for normal operation.

6.2. Нормалдуу иштөө

After calibration, connect the battery with the throttle stick at minimum. The ESC will arm, indicated by a specific tone. You can then slowly advance the throttle to control the motor speed. Always ensure the propeller is clear before applying throttle.

7. Programming the ESC

The ZTW Mantis G2 85A ESC offers various programmable parameters to fine-tune its performance to your specific aircraft and preferences. Programming can be done using either the ZTW LCD Program Card G2 or the dedicated Android/iOS mobile application.

7.1. Programmable Parameters (Exampа)

• Тормоз түрү: Off, Soft, Medium, Hard.
• Убакыт: Low, Medium, High (adjusts motor efficiency and temperature).
• Cut-off Voltage: Көлөмдү коётtage at which the ESC reduces or cuts power to protect the battery.
• Баштоо режими: Normal, Soft, Super Soft.
• SBEC Voltage: 6V, 7.4V, 8.4V.
• Мотордун айлануусу: Normal, Reverse.

Refer to the specific instructions provided with the ZTW LCD Program Card G2 or within the mobile application for detailed steps on how to connect and adjust these parameters.

8. Техникалык тейлөө

Regular inspection and basic maintenance will help ensure the longevity and reliable performance of your ESC:

• Тазалоо: Keep the ESC free from dust, dirt, and debris. Use a soft brush or compressed air to clean the heat sink fins.
• Туташуу текшерүү: Periodically inspect all wire connections (motor, battery, receiver) for signs of wear, corrosion, or loose contacts.
• Физикалык зыян: Check the ESC casing and wires for any physical damage after each flight.
• Сактагыч: Store the ESC in a dry, cool environment away from direct sunlight and extreme temperatures.

9. Кыйынчылыктарды

If you encounter issues with your ZTW Mantis G2 85A ESC, refer to the following common problems and solutions:

• Мотор айланбай жатат:
  • Батареянын туташуусун жана заряд деңгээлин текшериңиз.
  • Verify throttle signal cable is securely connected to the receiver.
  • Perform throttle range calibration again.
  • Ensure motor wires are correctly connected and not shorted.
• Мотор туура эмес багытта иштейт:
  • ESC менен мотордун ортосундагы үч мотор зымынын каалаган экөөсүн алмаштырыңыз.
  • Alternatively, reverse motor direction using the programming options.
• ESC Overheats:
  • ESC айланасында жетиштүү аба айланышын камсыз кылыңыз.
  • Check if the propeller is too large or motor timing is too aggressive (adjust via programming).
  • Батареянын көлөмүн текшериңизtage and current draw are within specifications.
• Intermittent Power/Loss of Control:
  • Check all connections for looseness or corrosion.
  • Inspect for damaged wires or solder joints.
  • Ensure receiver and transmitter are functioning correctly and within range.

10. Кепилдик жана колдоо

For warranty information and technical support regarding your ZTW Mantis G2 Series 85A ESC, please contact the retailer or the manufacturer, ZTW, directly. For purchases made through Buddy RC, please reach out to Buddy RC customer service for assistance.

Ар кандай кепилдик дооматтары үчүн сатып алуунун далили катары сатып алуу дүмүрчөгүңүздү сактаңыз.