Radiomaster Multi-Protocol Receiver R81, R84, R86, R86C, R88 Instruction Manual

1. Продукт бүтүп калдыview

This manual provides detailed instructions for the Radiomaster series of multi-protocol receivers, including models R81, R84, R86, R86C, and R88. These receivers are designed for use with FPV drones and other RC applications, offering compatibility with Frsky D8 protocol and various channel configurations (4CH, 6CH, 8CH) with PWM and SBUS output options.

Please ensure to verify the model and part number for compatibility before installation.

2. Техникалык шарттар

Below are the detailed specifications for each receiver model:

2.1. Radiomaster R81 Receiver

2.2. Radiomaster R84 4CH Receiver

Image: Radiomaster R84 4CH Receiver, showing its compact size and pin configuration for channels 1-4 and power input.

2.3. Radiomaster R86 6CH Receiver

2.4. Radiomaster R86C Receiver

2.5. Radiomaster R88 8CH Receiver

3. Орнотуу жана байлоо боюнча нускамалар

This section outlines the general procedure for setting up and binding your Radiomaster receiver to a compatible transmitter (e.g., Radiomaster TX16S, SE).

3.1. Pre-binding Checklist

• Ensure your transmitter is powered on and set to the correct protocol (Frsky D8).
• Verify the receiver is correctly connected to a power source within its specified voltage range (e.g., 4.5-8.4V for R84, R86, R86C, R88; 4.5-6V for R81).
• Бардык туташуулар коопсуз экенин текшериңиз.

3.2. Байлоо жол-жобосу

1. Power On Receiver in Bind Mode: Connect power to the receiver while holding down the bind button (if present) or follow the specific power-on sequence for bind mode. For most Radiomaster R-series receivers, the LED will flash rapidly indicating bind mode.
2. Activate Bind Mode on Transmitter: On your Radiomaster transmitter, navigate to the model setup menu. Select the Frsky D8 protocol. Choose the "Bind" option.
3. Байланышты ырастоо: The receiver's LED should change from rapidly flashing to solid, indicating a successful bind. If the LED continues to flash, repeat the binding process.
4. Сыноо байланыштары: After successful binding, power cycle both the transmitter and receiver. Test all control surfaces and functions to ensure proper communication.

Note: Specific bind button locations or power-on sequences may vary slightly between receiver models. Refer to your transmitter's manual for detailed binding instructions.

4. Операция

Once bound, the receiver will establish a connection with your transmitter upon power-up. Ensure your transmitter is powered on first, then power on your model with the receiver. The receiver's LED should illuminate solid, indicating a stable connection.

4.1. Channel Output

• PWM чыгаруу: Models like R84, R86, R86C, and R88 provide individual PWM outputs for each channel. Connect your servos or ESCs directly to the corresponding pins.
• SBUS чыгаруусу: The R81 and R86C models also offer SBUS output. SBUS allows for a single wire connection to flight controllers, transmitting all channel data digitally.

4.2. RSSI Telemetry

All listed Radiomaster R-series receivers support RSSI (Received Signal Strength Indicator) telemetry. This feature allows your transmitter to display the signal strength received by the receiver, providing critical information about link quality during flight. Consult your flight controller or transmitter manual for instructions on how to enable and display RSSI data.

5. Техникалык тейлөө

Proper maintenance ensures the longevity and reliable operation of your receiver.

• Физикалык текшерүү: Regularly inspect the receiver for any physical damage, loose wires, or corrosion.
• Антеннаны жайгаштыруу: Ensure antennas are properly positioned and not obstructed by carbon fiber or metal components. Avoid sharp bends in the antenna wires.
• Курчап турган чөйрөнү коргоо: Protect the receiver from moisture, dust, and extreme temperatures. Consider using conformal coating or heat shrink for added protection in harsh environments.
• Программалык камсыздоонун жаңыртуулары: Periodically check the Radiomaster official website for any available firmware updates for your receiver or transmitter. Updates can improve performance and add new features.

6. Кыйынчылыктарды

If you encounter issues with your receiver, consider the following troubleshooting steps:

• No Link/No Control:
  • Verify the receiver is correctly bound to the transmitter. Re-bind if necessary.
  • Check that the transmitter is powered on and set to the correct protocol (Frsky D8).
  • Кабыл алгыч көрсөтүлгөн кубаттуулуктун чегинде жетиштүү кубаттуулукту алып жатканын текшериңизtage диапазону.
  • Бардык зымдарды бош туташуулар же бузулуулар үчүн текшериңиз.
  • Check antenna placement; ensure they are not shielded or damaged.
• Үзүлгүс сигнал/кыска диапазон:
  • Check for sources of interference (e.g., other 2.4GHz devices, noisy ESCs, FPV video transmitters).
  • Ensure antennas are positioned optimally, away from carbon fiber, metal, and other electronics.
  • Verify the transmitter's RF power setting is appropriate.
  • Антенналардын бузулгандыгын текшериңиз.
• Incorrect Channel Output:
  • Confirm the correct output format (PWM/SBUS) is selected on your flight controller or device.
  • Check channel mapping on your transmitter and flight controller.

7. Кепилдик жана колдоо

For warranty information, technical support, or service inquiries, please refer to the official Radiomaster webсайтка же ыйгарым укуктуу дилериңизге кайрылыңыз. Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.

Өндүрүүчү: HePbak

Биринчи жеткиликтүү датасы: 16-октябрь, 2023-жыл