Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Total Automatic Self-priming Jet Pump, model TWP415006. Please read this manual thoroughly before operating the pump to ensure proper use and to prevent damage or injury.
Коопсуздук нускамалары
Өрт, электр шок же жаракат алуу коркунучун азайтуу үчүн ар дайым төмөнкү коопсуздук чараларын сактаңыз:
- Электр коопсуздугу: Электр энергиясы насостун көлөмүнө дал келүүсүн текшериңизtage (220-240V~50Hz). Always connect the pump to a properly grounded outlet. Do not operate the pump with a damaged cord or plug.
- Суу коопсуздугу: Do not pump flammable or corrosive liquids. Ensure the pump is not submerged unless specifically designed for submersible use. Protect the pump from freezing temperatures.
- Орнотуу: Install the pump in a dry, well-ventilated area, protected from direct sunlight and rain. Ensure stable mounting to prevent vibration.
- Тейлөө: Disconnect power before performing any maintenance or repairs. Only qualified personnel should perform repairs.
- Балдар жана үй жаныбарлары: Иштеп жатканда балдарды жана үй жаныбарларын насостон алыс кармаңыз.
Продукт бүттүview жана компоненттер
The Total Automatic Self-priming Jet Pump TWP415006 is designed for efficient water transfer. It includes a 24L cylindrical tank, pressure switch, pressure gauge, stainless steel hose, and brass 3-way connector.
Figure 1: ашыкview of the Total Automatic Self-priming Jet Pump TWP415006.
Figure 2: Key features of the pump, including 1500W power, 24L tank, and copper wire motor.
Камтылган компоненттер:
- 1 x Automatic Self-priming Jet Pump (1.5kW)
- 1 x 24L Cylindrical Tank
- 1 х басым которгуч
- 1 x Stainless Steel Hose
- 1 х Манометр
- 1 x Brass 3-way Connector
Техникалык шарттар
| Параметр | Нарк |
|---|---|
| Модел | TWP415006 |
| Тtage | 220-240V~50Hz |
| Номиналдуу кубаттуулук | 1500 Вт (2.0 HP) |
| Макс. Flow | 100 л/мин |
| Макс. Баш | 60 м |
| Макс. Сорох | 9m |
| Түтүк диаметри | 1" x 1" |
| Мотор түрү | Copper Wire Motor |
| Дөңгөлөктүү материал | Дат баспаган болот |
| Насос корпусу | Электрофорез |
| Вал материалы | Stainless Steel Welding (304+45#) |
| Кабелдин узундугу | 0.3 м |
| Элемент Салмагы | 32 килограмм |
| Пакеттин өлчөмдөрү | 62.7 x 57.3 x 36 см |
Жайгашуу
1. Жайгаштыруу
- Choose a flat, stable, and dry location for the pump, protected from direct weather exposure.
- Ensure adequate ventilation around the pump.
- Position the pump as close as possible to the water source to minimize suction lift.
2. Түтүк туташтыруу
- Соргуч түтүк: Connect a rigid pipe of 1" diameter to the suction inlet. Ensure the suction pipe is airtight to prevent air leaks, which can affect priming and pump performance. Install a foot valve with a strainer at the end of the suction pipe in the water source to prevent debris from entering the pump and to maintain prime.
- Агызуучу түтүк: Connect a 1" diameter pipe to the discharge outlet. The included stainless steel hose and brass 3-way connector should be used for the pressure tank and pressure gauge connection.
- Use thread sealant tape on all threaded connections to ensure a watertight seal.
3. Электр байланышы
- Ensure the power supply is 220-240V~50Hz.
- Connect the pump to a dedicated, properly grounded electrical outlet.
- Do not use extension cords unless absolutely necessary, and if so, ensure they are rated for outdoor use and the pump's power requirements.
4. Насосту толтуруу
- Before first use, or if the pump has run dry, it must be primed.
- Locate the priming plug on the top of the pump casing.
- Remove the priming plug and slowly fill the pump casing таза суу менен ашып кеткенче чайкаңыз.
- Праймер сайгычын бекем ордуна коюңуз.
- Ensure the discharge valve is open before starting the pump.
Иштөө нускамалары
1. Насосту ишке киргизүү
- Ensure the pump is properly primed (see Setup section).
- Бардык байланыштар коопсуз жана агып кетпегендигин текшериңиз.
- Plug the pump into the grounded electrical outlet. The pump will start automatically when pressure drops below the set point of the pressure switch.
2. Мониторингдин иштеши
- Observe the pressure gauge to ensure the system is operating within expected pressure ranges.
- Көйгөйдү көрсөтүшү мүмкүн болгон адаттан тыш ызы-чууларды же термелүүлөрдү угуңуз.
- Check for any leaks around connections.
3. Өчүрүү
- To stop the pump, simply unplug it from the power source. The automatic pressure switch will also stop the pump when the desired pressure is reached.
- For extended periods of non-use, especially in freezing conditions, drain the pump and pipes completely to prevent damage.
Техникалык тейлөө
1. Үзгүлтүксүз текшерүүлөр
- Periodically inspect the pump and all connections for signs of wear, damage, or leaks.
- Check the pressure tank's air charge annually. Refer to the tank's specific instructions for proper air pressure.
- Ensure the foot valve strainer is clear of debris.
2. Тазалоо
- Keep the pump exterior clean and free of dust and dirt to ensure proper cooling.
- Катуу химиялык заттарды же абразивдүү тазалоочу каражаттарды колдонбоңуз.
3. Кышка даярдык (суук климат үчүн)
- If the pump is installed in an area subject to freezing temperatures, it must be drained completely to prevent damage from ice expansion.
- Disconnect power, open all drain plugs, and remove the priming plug to allow all water to escape.
- Store the pump in a warm, dry place if possible.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Насос иштебейт | No power; tripped circuit breaker; faulty motor. | Check power connection and circuit breaker. Consult a qualified electrician if motor is suspected faulty. |
| Насос иштейт, бирок суу агып чыкпайт | Pump not primed; air leak in suction line; clogged foot valve/strainer; low water level in source. | Re-prime the pump. Check all suction connections for leaks. Clean foot valve strainer. Ensure adequate water in source. |
| Төмөнкү басым же агым | Partial air leak; clogged impeller; worn components; incorrect pipe size. | Check suction line for small leaks. Inspect and clean impeller. Consult service for worn parts. Ensure correct pipe diameter. |
| Насостун циклдары өтө көп | Pressure tank air charge too low; leak in system; faulty pressure switch. | Check and adjust pressure tank air charge. Inspect entire system for leaks. Test or replace pressure switch. |
| Ашыкча ызы-чуу/титирөө | Cavitation (air in pump); loose mounting; bearing wear. | Ensure pump is primed and no air leaks. Secure pump mounting. Consult service for bearing issues. |
Кепилдик жана колдоо
TOTAL products are manufactured to high-quality standards and are guaranteed against manufacturing defects. For warranty claims or technical support, please contact your local TOTAL authorized service center or the retailer from whom you purchased the product. Please retain your proof of purchase for warranty validation.
Кошумча жардам алуу үчүн, сиз иш сапары менен болот TOTAL Store on Amazon.
