1. Киришүү
The SUNLU Filament Connector FC01 is designed to fuse remaining 3D printer filament, maximizing material usage and reducing waste. It allows for the creation of multi-color prints by joining filaments of the same material but different colors. Featuring fast and precise heating, a wide range of compatibility, and user-friendly operation, this device enhances the 3D printing experience.
2. Коопсуздук маалыматы
- Caution Hot Surface: The heating element reaches high temperatures (up to 240°C). Avoid direct contact with the heating element during and immediately after operation to prevent burns.
- Электр камсыздоо: Use a 5V 2A power adapter (not included) to ensure correct operation. Using an incorrect power adapter may damage the device or pose a safety risk.
- Вентиляция: Ensure adequate ventilation when fusing filaments, especially materials like ABS, which may release fumes.
- Балдар жана үй жаныбарлары: Аппаратты балдар жана үй жаныбарлары жетпеген жерде сактаңыз.
3. Пакеттин мазмуну
Пакетиңизде бардык буюмдар бар экенин текшериңиз:
- Filament Connector device
- USB кабели
- PTFE Sleeves (200 pieces) for fusing filament ends
- Usage Instructions Manual
Figure 3.1: SUNLU Filament Connector FC01 Package Contents. Includes the main unit, USB cable, PTFE sleeves, and user manual.
4. Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Бренд | СУНЛУ |
| Модель номери | FC01 |
| Filament диаметри | 1.75 мм |
| Шайкеш материалдар | PLA, PETG, ABS, PA, Nylon, PC |
| Maximum Heating Temperature | 240°C |
| Typical Heating Time (to 185°C) | Болжол менен 3 мүнөт |
| Power Input Recommendation | 5V 2A (Adapter not included) |
| Өлчөмдөр | 3.94 x 3.15 x 1.18 дюйм |
| Элемент Салмагы | 4.9 унция |
5. Орнотуу
- Туташуу кубаты: Connect the provided USB cable to the Filament Connector. Plug the other end into a 5V 2A power adapter (not included) and then into a power outlet.
- Күйгүзүү: Press the power button on the device. The display screen will illuminate.
- Жиптин түрүн тандаңыз: Use the setting key to cycle through filament types (PLA, PETG, ABS, PA/PC, PCL). The device will automatically set a default fusion temperature for the selected material.
- Температураны тууралоо (милдеттүү эмес): If needed, use the up/down keys to fine-tune the fusion temperature. The maximum temperature is 240°C.
- Жылытууну күтүңүз: Allow the device to heat up to the set temperature. The display will show the current temperature (PV) and the set temperature (SV). The device will beep once the target temperature is reached.
Figure 5.1: Basic Setup and Operation Steps.
6. Иштөө нускамалары
Follow these steps to effectively fuse 1.75mm 3D printer filaments:
- Жипчелерди даярдоо: Ensure both filament ends to be joined are of the same material. Cut both ends at an oblique angle (approximately 45 degrees) to maximize contact area.
- PTFE жеңин салыңыз: Slide one of the provided PTFE sleeves over one of the filament ends.
- Align Filaments: Insert the other filament end into the PTFE sleeve, ensuring the cut ends meet inside the sleeve. Rotate the filaments to find the appropriate angle that minimizes the gap at the joint.
- Place in Heating Slot: Once the device has reached the set temperature and beeped, open the heating cover. Carefully place the connected portion of the filament (with the PTFE sleeve) inside the heating slot.
- Apply Pressure During Heating: Close the heating cover. During the heating process (typically 7-10 seconds for PLA), hold both sides of the filament and gently push inwards for 1-2 seconds to ensure proper fusion. The device will beep again when the fusion time is complete.
- Алып салуу жана муздатуу: Once the fusion time is reached, slowly remove the fused filament from the heating slot. Turn off the power to prevent accidental burns. Allow the fused filament to cool for 5-10 seconds, optionally using a fan to speed up cooling.
- Trim Excess Sleeve: Once cooled, place the filament ends into the cutting slot on the device. Press the top cover down firmly. The blade under the cutting slot will cut the PTFE sleeve. Remove the filament and the cut sleeve.
Video 6.1: Detailed step-by-step instructions for using the SUNLU Filament Connector FC01 to fuse 3D printer filaments. This video demonstrates power connection, temperature setting, filament preparation, fusion process, cooling, and trimming of the PTFE sleeve.
Figure 6.2: Tips for optimal filament fusion, including proper cutting, placement, pressure application, and cooling.
7. Filament Compatibility and Temperature Settings
The Filament Connector FC01 is compatible with various 1.75mm 3D printing filaments. Refer to the table below for default melting temperatures and recommended fusion times:
| Filament Type | Демейки эрүү температурасы | Жылытуу убактысы | Сунушталган эрүү убактысы |
|---|---|---|---|
| PCL сериясы | 85°C | 1 мин. | 5s үчүн 6s |
| PLA сериясы | 185°C | 3 мин. | 7s үчүн 8s |
| ABS сериясы | 220°C | 3 - 4 мүн. | 7s үчүн 8s |
| PETG сериясы | 210°C | 3 - 4 мүн. | 7s үчүн 8s |
| PA/PC сериялары | 230°C | 5 мин. | 9s үчүн 10s |
Figure 7.1: Filament Compatibility and Recommended Settings.
8. Техникалык тейлөө
To ensure the longevity and optimal performance of your Filament Connector FC01:
- Тазалоо: After use, ensure the heating element and surrounding areas are free from any filament residue. Use a soft, dry cloth to clean the device. Do not use liquids or abrasive cleaners.
- Сактагыч: Аппаратты күн тийбеген жана нымдуулуктан алыс салкын, кургак жерде сактаңыз.
- PTFE Sleeves: Replace PTFE sleeves as needed. The package includes 200 sleeves for extended use.
9. Кыйынчылыктарды
- Filament Not Fusing Properly:
- Ensure the filament ends are cut at a sharp oblique angle for maximum contact.
- Verify that the correct temperature for the filament type is selected.
- Apply gentle, consistent pressure during the fusion process.
- Ensure the filament is properly centered in the heating slot.
- Түзмөк жылытылбайт:
- Check if the USB cable is securely connected.
- Ensure the power adapter is 5V 2A and properly plugged into a working outlet.
- Аппаратты күйгүзүү үчүн кубат баскычын басыңыз.
- Filament Snapping After Fusion:
- Allow sufficient cooling time after fusion before handling or applying tension.
- Avoid excessive pressure during the fusion process, which can deform the filament.
10. Кепилдик жана колдоо
For warranty information and technical support, please refer to the official SUNLU webсайтка же түздөн-түз кардарларды тейлөөгө кайрылыңыз. Кепилдик дооматтар үчүн сатып алуу дүмүрчөгүңүздү сактаңыз.
