GEPRC Vapor-X5 HD O4 Pro FPV Drone Instruction Manual

1. Киришүү

This manual provides essential information for the safe and efficient operation of your GEPRC Vapor-X5 HD O4 Pro FPV Drone. Please read this manual thoroughly before using the product to ensure proper setup, flight, and maintenance.

The Vapor-X5 HD O4 Pro is a high-performance FPV drone designed for immersive flight experiences and high-definition video capture. It features a robust frame, powerful motors, and advanced flight control systems, including GPS for enhanced stability and navigation.

Image: The GEPRC Vapor-X5 HD O4 Pro FPV Drone, showcasing its design and propellers.

2. Коопсуздук боюнча көрсөтмөлөр

• Жергиликтүү эрежелер: Always check and comply with local drone regulations and laws before flying. This drone weighs 409g, which typically requires registration and adherence to specific flight rules in many regions.
• Учуу алдында текшерүү: Before each flight, inspect the drone for any damage, ensure propellers are securely attached, and verify battery levels.
• Экологиялык шарттар: Avoid flying in strong winds, rain, fog, or other adverse weather conditions.
• Көрүү сызыгы: Maintain visual line of sight with your drone at all times.
• Тоскоолдуктар: Fly in open areas, away from people, buildings, trees, and power lines.
• Батареянын коопсуздугу: Use only recommended batteries and follow proper charging and storage procedures.
• Пропеллердин коопсуздугу: Колдоруңузду жана бетиңизди айлануучу пропеллерлерден алыс кармаңыз.

3. Пакеттин мазмуну

Төмөндө тизмеленген нерселердин баары пакетиңизге камтылганын текшериңиз:

Камтылган заттар:

• 1 x Vapor-X5 O4 Pro Drone
• 2 x GEMFAN 5136 Propellers
• 2 x Battery anti-slip pads
• 1 x Spare screw pack
• 1 x Vapor side panel
• 2 x M20*250mm battery straps
• 1 х L түрүндөгү бурагыч 1.5 мм
• 1 х L түрүндөгү бурагыч 2.0 мм
• 1 x GoPro mount

Spare Screw Pack Includes:

• 6 x M3*10mm round head screws
• 6 x M3*8mm round head screws
• 2 x M3*6mm flat head screws
• 1 x M5*28mm thin head screw
• 1 x M5 flange nut
• 4 x M3 rivet nuts

4. Орнотуу

4.1. Receiver Installation and Binding (PNP Version)

As a Plug-N-Play (PNP) version, the GEPRC Vapor-X5 O4 Pro does not include a pre-installed receiver. You will need to install a compatible receiver (e.g., GEPRC ELRS24 or TBS Nano RX) and bind it with your remote controller. Refer to your chosen receiver's manual for specific installation and binding instructions.

4.2. Camera and VTX Module Installation

The O4 Pro Camera and VTX module require careful installation to ensure optimal performance and vibration dampening. Follow these general steps, referring to the provided video for visual guidance:

1. Insert the O4 camera into its camera bracket, ensuring the connector faces the canopy.
2. Install the shock-absorbing balls into the camera bracket slots.
3. Place the camera and bracket assembly into the canopy, aligning the holes. Secure with M2*4 flat head socket cap screws.
4. Install the VTX shock absorption module. Insert the 6.6mm shock-absorbing balls into the module's holes, ensuring the higher end faces down.
5. Connect the 6Pin connector cable to the O4 VTX module and the VTX antenna to its connector.
6. Place the O4 VTX module onto the flight controller, aligning the holes with the flight control unit.
7. Tighten the forward shock-absorbing ball of the O4 VTX module with an M1.4*10*4 Phillips flat washer head tapping screw.
8. Place the canopy onto the O4 VTX module, ensuring the camera faces forward and the canopy holes align with the shock-absorbing balls.
9. Pass the VTX antenna through the rear hole of the canopy.
10. Tighten the canopy with three M1.4*10*4 Phillips flat washer head tapping screws.
11. Replace the camera cable using tweezers, ensuring it is suspended to reduce vibration and prevent touching the canopy.

4.3. Батареяны орнотуу

Securely attach the recommended 6S LiPo 1300mAh – 1800mAh battery to the top plate using the provided battery straps. Ensure the battery is centered for optimal balance and that the anti-slip pads prevent movement during flight. Connect the XT60 connector to the drone's power port.

5. Иштөө нускамалары

5.1. Учуу алдындагы текшерүү тизмеси

• Ensure all components (drone, remote controller, FPV goggles) are fully charged.
• Verify propellers are correctly installed and free from damage.
• Check for any loose screws or connections.
• Confirm GPS signal acquisition before takeoff (drone will beep when satellites are acquired).
• Perform a quick visual inspection of the flight area for any potential hazards.

5.2. Учуу режимдери жана башкаруу элементтери

The Vapor-X5 O4 Pro supports various flight modes. Familiarize yourself with your remote controller's manual for specific mode activation and control schemes. For FPV flight, ensure your goggles are properly configured and displaying a clear video feed.

5.3. GPS функциясы

The integrated GEP-M10 GPS module provides enhanced stability and safety features. Ensure GPS lock is achieved before takeoff. Key GPS features include:

• Position Hold: Maintains the drone's position automatically.
• Үйгө кайтуу (ҮҮ): Automatically flies the drone back to its takeoff point in case of signal loss or low battery.

It is mandatory to configure and test GPS failsafe settings in your flight controller software (e.g., Betaflight) to ensure safe operation in case of signal loss.

5.4. Video Recording and Photography

The O4 Pro Camera captures high-definition video and still images. Refer to your FPV system's documentation for instructions on how to start/stop recording and capture photos. The drone features 46GB of internal storage for recorded footage.

6. Техникалык тейлөө

6.1. Тазалоо

Regularly clean your drone to remove dust, dirt, and debris. Use a soft, dry cloth for the frame and components. For the camera lens, use a specialized lens cleaning cloth and solution.

6.2. Пропеллерди алмаштыруу

Inspect propellers for cracks, bends, or chips before each flight. Damaged propellers can lead to unstable flight and potential crashes. To replace:

1. Power off the drone and remove the battery.
2. Carefully remove the damaged propeller by unscrewing the M5 flange nut.
3. Install a new GEMFAN 5136 propeller, ensuring it is oriented correctly (clockwise or counter-clockwise as indicated on the motor/propeller).
4. Secure with the M5 flange nut, ensuring it is tight but not overtightened.

6.3. Батареяга кам көрүү

• Заряддоо: Use only a compatible LiPo charger. Never leave charging batteries unattended.
• Сактагыч: LiPo батарейкаларын сактоо көлөмүндө сактаңызtage (typically 3.8V per cell) in a fire-safe bag or container.
• Жоюу: Бузулган же шишип кеткен батареяларды жергиликтүү эрежелерге ылайык коопсуз жок кылыңыз.

6.4. Микропрограмманы жаңыртуу

Periodically check the GEPRC official website for firmware updates for your drone's flight controller (GEP-F722-HD v2) and O4 Air Unit Pro. Keeping firmware updated ensures optimal performance, new features, and bug fixes.

7. Кыйынчылыктарды

8. Техникалык шарттар

9. Кепилдик жана колдоо

For warranty information, technical support, or service inquiries, please refer to the official GEPRC webсайтка же ыйгарым укуктуу дилериңизге кайрылыңыз. Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.