Introduction
The Televes SmartKom 531983 is an intelligent signal combiner and amplifier designed to optimize over-the-air (OTA) television reception. This device addresses challenges associated with receiving signals from multiple broadcast directions and managing uneven channel levels. It integrates signals from up to three antennas, filters each channel individually, and balances output levels for consistent reception.
The SmartKom features 32 per-channel filters, Bluetooth app control for advanced configuration, and is compatible with ATSC 3.0 (NextGen TV) and 4K broadcasts. It provides a single, clean output for whole-home distribution or small commercial applications.
Жайгашуу
Кутуда эмне бар
- SmartKom Unit
- Кубат менен камсыздоо контроллери
- Коаксиалдык кабель
- Weather Boots
- Туташтыргычтар
Монтаждоо
The SmartKom unit can be mounted outdoors on a mast using its weather-resistant Zamak and ABS enclosure, or indoors on a wall. Select a location that allows for easy connection to your antennas and the power supply.
Байланыштар
Connect up to three antennas to the designated input ports on the SmartKom unit. The unit is powered over the same coaxial cable that carries the signal from the SmartKom to the included power supply controller. The power supply controller then connects to your television or distribution system.
Figure 1: SmartKom Mast Amplifier and Power Supply Unit Diagram. This comprehensive diagram identifies all key components of both the SmartKom Mast Amplifier and its Power Supply Unit. It labels the antenna inputs, output, auto-scan button, and provides a guide to the LED indicators for configuration and status.
Figure 2: Typical Installation Diagram. An illustrative diagram demonstrating a common installation scenario for the SmartKom. It shows how multiple antennas are connected to the SmartKom, which then feeds a single signal to a power supply, a splitter, and finally to multiple televisions within a home.
Initial Configuration (Auto-Scan)
- Ensure all antennas are connected and the power supply is active.
- Press and hold the auto-scan button on the SmartKom unit for approximately 5 seconds.
- The SmartKom will automatically scan all inputs, identify available channels, apply filtering, and balance the signal levels. It also provides power to compatible Televes antennas or preampаман калгандар.
Advanced Configuration (ASuite App)
For detailed control and fine-tuning, download the free ASuite app (available for iOS and Android devices). The app connects wirelessly via Bluetooth, allowing you to select specific channels per input and adjust individual channel levels from the ground.
Иштөө нускамалары
Сигнал иштетүү
The SmartKom's 32 programmable digital filters operate on a channel-by-channel basis with a 60 dB dynamic range. Each channel is individually amplified and balanced to a consistent output level, regardless of the incoming signal strength. This process prevents strong channels from overpowering weaker ones.
Multi-Antenna Operation
When multiple antennas are connected, the SmartKom individually filters each channel from each antenna input, rejects off-axis contributions, and adjusts each channel to the same output level. This delivers a single, balanced, and interference-free signal, making all channels from all directions available simultaneously.
LTE/5G Filtering
The unit includes built-in LTE and 5G cell signal filtering (above 608 MHz) to block common sources of OTA interference and overload, ensuring a cleaner signal.
LED көрсөткүчтөрү
The SmartKom and its Power Supply Unit feature LED indicators to provide status information:
| Статус | Көрсөтмө | LED жүрүм-туруму |
|---|---|---|
| SCAN | Каналдар изделүүдө | ЖАЯН БИЛИК |
| ЖӨНДӨӨ | Тууралоо | FAST BLINK |
| ON | Күйгүзүлгөн | ON |
| Статус | Көрсөтмө | LED жүрүм-туруму |
|---|---|---|
| Short circuit or overconsumption at input port (S) | Ката абалы | ЖАЯН БИЛИК |
| ON | Кадимки иштөө | ON |
Техникалык тейлөө
The SmartKom unit is designed for durability with a weather-resistant Zamak and ABS enclosure, suitable for outdoor mast mounting. No specific routine maintenance is typically required beyond ensuring connections remain secure and free from corrosion.
Configuration settings are saved in memory and are retained even after a power loss, eliminating the need for re-setup.
Periodically inspect the unit and its connections for any signs of physical damage or wear, especially if mounted outdoors.
Проблемаларды чечүү
No Channel Reception / Zero Signal
- Электр камсыздоо: Ensure the included power supply controller is correctly connected and powered. The SmartKom requires power via the coaxial cable from this unit. Check the Status LED on the Power Supply Unit (PSU) for an 'ON' indication. If it's blinking slowly, there might be a short circuit or overconsumption.
- Байланыштары: Verify that all coaxial cables are securely connected to the correct input and output terminals on both the SmartKom and the power supply.
- Автоматтык түрдө скандоо: Perform an auto-scan as described in the Setup section to ensure the SmartKom has detected and configured channels.
ASuite App Communication Timeout
- Bluetooth Activity: The internal unit's Bluetooth connection remains active for approximately 2 hours. If you need to make adjustments after this period, power cycle the inside unit (unplug and re-plug the power supply) to restart the Bluetooth functionality.
- Колдонмонун Нускасы: Ensure your ASuite app is updated to the latest version.
- Түзмөктүн жакындыгы: Maintain a reasonable distance between your mobile device and the SmartKom unit for stable Bluetooth connection.
Scanning Issues / Signal Dropouts
- Complex Antenna Setups: If the auto-scan struggles with three antennas, try performing the initial scan with only two antennas connected. Once configured, you can manually add channels for the third antenna using the ASuite app.
- Каналды кол менен тандоо: Use the ASuite app to manually select which antenna receives which channel, especially if a strong channel is picked up by multiple antennas, or if auto-scan does not optimize reception for specific channels.
- Антеннаны багыттоо: Confirm that your antennas are correctly aimed towards broadcast towers. Resources like rabbitears.com can assist in identifying optimal directions and actual channel numbers (RF channels).
- Экологиялык факторлор: Extreme weather conditions can temporarily affect signal reception.
Техникалык шарттар
Figure 3: SmartKom Unit Dimensions. A diagram illustrating the physical dimensions of the SmartKom unit, providing measurements for installation planning.
| Өзгөчөлүк | Деталь |
|---|---|
| Модель номери | 531983 |
| Өндүрүүчү | Телевизорлор |
| Монтаж түрү | Mast-Mounted |
| Number of Antenna Inputs | 3 |
| Чыгуу күчү | 25000 Milliwatts (25 dBmV fixed, maintained by AGC) |
| Материал | Zinc Alloy (Zamak and ABS enclosure) |
| Элемент Салмагы | 1.91 фунт |
| Пакеттин өлчөмдөрү | 7.68 x 6.97 x 2.32 дюйм |
| Чыпкалоо | 32 per-channel digital filters, LTE/5G filtering (above 608 MHz) |
| Control | Auto-scan button, ASuite app via Bluetooth |
| Шайкештик | ATSC 3.0 (NextGen TV), UHD 4K OTA broadcasts |
Кепилдик маалымат
For detailed warranty information regarding your Televes SmartKom unit, please refer to the official Televes webсайтына кириңиз же алардын кардарларды тейлөө кызматына түз кайрылыңыз. Кепилдик шарттары жана эрежелери аймакка жана сатып алуу күнүнө жараша өзгөрүшү мүмкүн.
Колдоо
If you require further assistance, have questions about installation, or need technical support, please visit the official Televes website for resources, FAQs, and contact information for their customer service department.
You can also refer to the ASuite app for additional guidance and advanced configuration options.
