Introduction
The GODOX RT-16 Wireless Flash Trigger Set is designed to provide reliable wireless synchronization for studio monolights and strobe flashes. Operating on a 433MHz frequency, it offers 16 selectable channels for interference-free operation. This set includes one transmitter and one receiver, enabling remote control of your flash units.
The system supports a synchronization speed of up to 1/200s and has a wireless control range of up to 30 meters. It is compatible with a wide range of camera brands including Fujifilm, Canon, Nikon, Olympus, and Pentax. Please refer to the compatibility list for specific models.
Note: This product is not compatible with Sony MI hotshoe cameras or Canon 1500D, 3000D, and 200D Mark II models.
Жайгашуу
1. Батареяны орнотуу
The transmitter requires a 12V 23A battery, and the receiver requires two AAA batteries (not included). Ensure correct polarity when inserting batteries.
Image: Transmitter battery compartment. The transmitter uses a 12V 23A battery. Remove the screw under the 'QC PASS' label to access the compartment.
Image: Receiver battery compartment. The receiver requires two AAA batteries. Ensure to remove any insulating film if present before inserting batteries.
2. Setting Channels
Both the transmitter and receiver feature dip switches to select one of 16 available channels. For proper operation, ensure both units are set to the same channel.
Image: Channel selection diagram. This diagram illustrates how to set the dip switches on both the transmitter and receiver to match one of the 16 available channels.
3. Connecting to Equipment
Mount the transmitter onto your camera's hotshoe. Connect the receiver to your studio strobe or monolight using the appropriate sync cable. The receiver has a 3.5mm jack, and a 3.5mm to 6.35mm adapter is included for compatibility with larger sync ports.
Image: Transmitter on camera and receiver connected to a studio strobe. This shows the typical setup for using the RT-16 system.
Image: 6.35mm adapter connection. The included adapter allows the receiver to connect to strobes with a 6.35mm sync port.
Иштөө нускамалары
1. Күйгүзүү
Ensure both the transmitter and receiver are powered on using their respective ON/OFF switches.
2. Сынап атуу
Press the test button on the transmitter to verify that the connected flash unit fires. The indicator light on the receiver should illuminate when a signal is received.
3. Camera Synchronization
Once the transmitter is mounted on your camera's hotshoe and the receiver is connected to your flash, take a picture. The flash unit should fire in sync with your camera's shutter.
4. Multiple Receivers
One RT-16 transmitter can control multiple RT-16 receivers simultaneously, provided all units are set to the same channel. This allows for multi-light setups.
Image: Multiple receiver setup. Illustrates how a single transmitter can wirelessly trigger multiple flash units equipped with RT-16 receivers.
Техникалык тейлөө
1. Батареяны алмаштыруу
When the indicator light on the transmitter or receiver becomes dim or the units fail to trigger reliably, it is time to replace the batteries. Refer to the battery installation section for guidance.
Video: How to change the L1028F battery in the RT-16 Transmitter. This video demonstrates the process of replacing the transmitter's battery.
2. Тазалоо
Use a soft, dry cloth to clean the exterior of the transmitter and receiver. Avoid using harsh chemicals or abrasive materials.
3. Сактоо
When not in use for extended periods, remove batteries from both units to prevent leakage. Store the set in a cool, dry place away from direct sunlight and extreme temperatures.
Проблемаларды чечүү
- Жарк этпейт:
- Өткөргүч жана кабыл алгыч күйгүзүлгөнүн текшериңиз.
- Verify that both units are set to the same channel.
- Check battery levels in both units and replace if necessary.
- Confirm the receiver is securely connected to the flash unit's sync port.
- Ensure the transmitter is properly seated on the camera's hotshoe.
- Inconsistent firing:
- Башка зымсыз түзмөктөрдөн мүмкүн болуучу тоскоолдуктарды текшериңиз.
- Өткөргүч менен кабыл алгычтын ортосундагы аралыкты азайтыңыз.
- Ensure there are no significant obstructions between the units.
- Шайкештик маселелери:
- Review the camera compatibility list provided in the setup section.
- Note that Sony MI hotshoe cameras and specific Canon models (1500D, 3000D, 200D Mark II) are not supported.
Техникалык шарттар
| Өзгөчөлүк | Спецификация |
|---|---|
| Модел | RT-16 |
| Иш жыштыгы | 433 МГц |
| Каналдар | 16 |
| Synchronization Speed | 1/200с чейин |
| Зымсыз башкаруу аралык | 30 метрге чейин |
| Transmitter Power Supply | 12V 23A батарея |
| Кабылдагычтын кубаттуулугу | 2 x AAA батарейкалар |
| Пакеттин өлчөмдөрү | 8.9 x 3.74 x 1.57 дюйм |
| Элемент Салмагы | 4.9 унция |
Image: Camera compatibility list. This table provides a detailed list of compatible camera brands and models for the RT-16 flash trigger.
Кепилдик жана колдоо
Кепилдик маалыматы жана техникалык колдоо үчүн расмий GODOXке кайрылыңыз webсайтка же сатуучуга кайрылыңыз. Бардык кепилдик дооматтар үчүн сатып алуу дүмүрчөгүңүздү сактаңыз.
You can find more information about GODOX products at the GODOX дүкөнү.
