HydroTab 300SR HTML Interceptor Set Instruction Manual

HydroTab 300SR HTML Interceptor Set

ТЕХНИКАЛЫК МААЛЫМАТТАР

DIMENSION

БОРБОР

КОНТРОЛЬЕРДИ ОРНОТУУ

1.  Place The HUB Drilling Pattern in the desired position, preferably a clean and easy-to-access area.
   МААНИЛҮҮ: The mounting area must be perfectly vertical!!
2. Drill the 4 holes, according to the provided drilling pattern, with 4 mm bore.
3. Mount The HUB, with the 4 provided screws.
4. Connect the NMEA, Ethernet & power cables to The HUB. The MFD will start displaying the main screen menu automatically, right after this step. Optionally, you can use the Ethernet Protection Cover – Part No. ELE-00833 (Fig. 4A).

МААНИЛҮҮ ЭСКЕРТҮҮ
If The HUB must be connected to a legacy network, it is necessary to use a PoE isolator.

Деңиз инженериясы
THE HUB – INSTALLATION ON AN EXISTING NMEA NETWORK DIAGRAM

THE HUB – DIRECT INSTALLATION DIAGRAM

THE HUB – MAIN SCREEN OVERVIEW

By tapping the Settings Menu Icon (Fig. 1), a pop-up window appears, with the following 3 options:

1.  Орнотуулар
2.  Pitch Profile Түзөтүү
3. Система маалыматы

Деңиз инженериясы
THE HUB – MENU SCREENS OVERVIEW – Жөндөөлөр

Орнотуулар

Page 1/4 contains:

• Кайыктын спецификациялары
• Interceptor Series
• Roll Sensitivity

Page 2/4 contains:

Boat Loading

• Reset Pitch and Roll
• Interceptor Calibration
• Air Unit Reset
• Микропрограмманы жаңыртуу
• Багыттоо

Page 3/4 contains:

•  Ылдамдыктын чеги
• Low Speed Retraction 1.12 Turn Rate Limit

Page 4/4 contains:

•  Active Pitch
• A Active Pitch Sensitivity

THE HUB – MENU SCREENS OVERVIEW – Жөндөөлөр

1. Кайыктын спецификациялары
   Includes Weight, Length and Max Speed of the vessel. Drag the bar on the slider to adjust each value individually.
2. Interceptor Series
   Select the Interceptor Series, installed on the vessel. Tap on the screen to select between SR Series, LS Series, or BT Series
3. Roll Sensitivity
   • Adjusts the deployment percentage of interceptors for each degree of roll inclination. The higher the sensitivity, the higher the deployment of interceptors, for every degree of roll inclination. Drag the bar on the slid-er to adjust roll sensitivity.
   • NOTE 1: High Roll Sensitivity may abruptly affect the vessel’s course and stability, especially in higher speeds.
   • NOTE 2: If you set the sensitivity at max value, it may cause overheating of the Air Unit, which will disable the Auto-Roll function, until the system cools down.
4. Boat Loading
   • Select between three available modes:
   • Light: When load is below normal weight Normal: Standard vessel load
   • Heavy: When the vessel is fully loaded
5. Reset Pitch and Roll
   Sets Pitch and Roll value to zero, according to the actual vessel position, at that time.
   Reset must be done, when the boat is in calm sea, with load evenly distributed onboard, so the plane defined by waterline is parallel to the sea plane.

Useful Tips for “Reset Pitch and Roll”:

• In case the vessel is slightly unbalanced (due to uneven weight distribution), follow the procedure bellow, for more accurate stability during Full Auto Mode:
• In calm sea, go to Manual Mode, adjust your boat position in order to be aligned with the horizon and then press Reset Pitch and Roll. This procedure will make your interceptors extend in an uneven position, in order to maintain the boat’s balance during Full Auto Mode.

Interceptor Calibration

• It calibrates both interceptors’ air pressure vs. extension.
• It should be executed after the initial installation, or after service works, when any of the interceptors is disconnected from the Air Unit.
• Calibration starts automatically. A pop-up screen appears, when the process is finished.

Air Unit Reset Resets the Air Unit

Микропрограмма Жаңыртуу

• Tap “Start” to initiate the Firmware
• Update process. Keep everything powered on, until the update is complete.
• NOTE: Make sure you are connected to a WiFi Network, before starting the Firmware Update. (See Pg. 11)

Багыттоо

• The HUB must be placed with a mounting angle, based on the vessel’s forward direction.
• The operator must enter the orientation degrees after the initial installation. Setting this value as accurately as possible is extremely crucial to The HUB’s optimal function.

Ылдамдыктын чеги

• Defines the maximum speed limit, after which the interceptors will retract.
• NOTE: Speed Limit is applied in ALL MODES.

Low Speed Retraction

• Enabled (Default): Retracts interceptors, when the vessel’s speed is lower than 6 knots.
• Disabled: Interceptors are retracted manually.
• ATTENTION! By disabling Low Speed Retraction, the interceptors will remain extended, and they can brake during haul out.

 Turn Rate Limit
This is the turn rate (in degrees per second), after which the system will stop using the full auto function, and balance the interceptors, in order not to affect the turn radius of the vessel.

 Active Pitch

• Adjusts the deployment percentage of interceptors for each degree of pitch. The higher the sensitivity, the higher the deployment of interceptors, for every degree of pitch.
• Tap the switch to enable the Active Pitch.
• Drag the bar on the slider to adjust pitch sensitivity.
• NOTE 1: High Pitch Sensitivity may abruptly affect the vessel’s course and stability, especially in higher speeds.
• NOTE 2: If you set the sensitivity at max value, it may cause overheating of the Air Unit, which will disable the Active Pitch function, until the system cools down.

THE HUB MENU SCREENS OVERVIEW – PITCH PROFILE

МААНИЛҮҮ ЭСКЕРТҮҮ:
After successfully entering all the necessary values in “Boat Specifications” screen, The HUB sets automatically a Pitch Profile Curve, which is stored in “Profile 1”. The vessel’s operator can create their own pitch profiles, or edit the already existing ones, through this menu screen.

THE HUB – WIFI SETUP
To access the WiFi Setup, tap the WiFi icon on the MFD Main Screen, which will lead to the following screen:

1. Tap the WiFi Network bracket, to drop down the list of the available WiFi networks.
2.  Каалаган тармакты тандаңыз.
3. Type the password, and then tap the Connect button.

• A highlighted text will appear after the (un)successful connection.
• An established WiFi connection is necessary, if you wish to update the device’s firmware (see. Pg. 11)

МААНИЛҮҮ ЭСКЕРТҮҮЛӨР

1. After the successful connection to a WiFi network, The HUB saves this network, for a quicker future connection, without having to type again the password.
2. The HUB does not connect automatically to any WiFi Network. Always connect The HUB to trusted networks.
3. Keep your network passwords in a safe and accessible place.

THE HUB – SYSTEM PROFILE МААЛЫМАТ
Displays useful information, such as IP Addresses, current software versions etc.

БҮЗГӨЛҮКТӨРДҮ ТҮЗҮҮ

If you are still having issues with The HUB, please contact Hydro Tab’s Technical Support Dpt. support@hydrotab.gr

Деңиз инженериясы

• Жоопкерчиликтен баш тартуу
  The interceptor units are also steering equipment and it is the sole responsibility of the navigator-operator to ensure that, at any point, any problem that will alter the vessel’s course, rising from malfunction of interceptors, should be dealt immediately by the operator.
  Under no circumstances, fault of our interceptor equipment leading to any kind of accident, creates liability for the manufacturer.
• Соода белгиси жөнүндө билдирүү
  Hydro Tab is a registered trademark of Olympic Engineering Ltd, Greece. All other trademarks, trade or company names referenced herein are used for identification only and are property of their respective owners.
• Патенттик билдирүү
  Hydro Tab products are protected by patents and industrial design patents, patents pending or design patents pending.
• Шайкештик декларациясы
  This product conforms to the following Electromagnetic Compatibility (EMC) regulations and standards for use in marine environments: CE EN 60945

Technical Information and Documentation

The technical information provided in this document was accurate and correct at the corresponding production time of the Hydro Tab interceptors. Our operating principal for improving the manufactured product, may lead to changes regarding its  specs, without prior notice. Liability will not be held for any inaccuracy, considering the product and the user manual.

Туура колдонуу билдирүүсү
This manual can be printed or copied for private use only. Copies should not be provided to third parties and manual should not be commercialized.

Продукцияны жок кылуу

Waste removal of this product must be done, according to the Waste Electrical and Electronic Equipment (WEEE) Directive.

Продукт каттоо
Кепилдик жарактуу болушу үчүн продуктуңузду онлайн каттаңыз.

• 4, Papazoglou Str. GR-17778 Athens Greece
• электрондук почта: info@hydrotab.gr
• webсайт: www.hydrotab.gr