igloo EK2 Keypad 2
Эмне камтылган
- A: Keypad
- B: Mounting Plate
- C: Mounting Screws
- D: Anchor Bolt
- E: Torx (T10) Screwdriver
- F: Батарея капкагы
Орнотуу кадамдары
Бурамалар менен монтаждоо
Find a place to install your Keypad. Installing it closer to your locks and entryway will enable easier operation.
Сизге эмне керек
- Step 1: Separate the Mounting Plate
Separate the mounting plate (B) from the keypad (A) by loosening the screw from below. Use the supplied Torx (T10) Screwdriver (E). - Step 2: Select Install Location
The Keypad 2 should be installed 86cm – 120cm (34 – 48 in) above the ground to ensure ADA compliance. Ensure that the keypad is not more than 5m away from the linked lock to ensure strong connectivity. 
Step 3: Mark Mounting Holes
Mark out two holes for securing the mounting plate (B). Use the mounting plate or Drill Sheet as a reference for marking the holes. The distance between the holes should be 80 mm / 3.15 in.
- 4-КАДАМ
МААНИЛҮҮ To ensure secure installation, use the recommended pilot hole and anchor bolt guidelines below. Mounting Pilot Hole Anchor Surface Diameter Bolt? Wood 2 mm / 5/64″ X Sheetmetal 2 mm / 5/64* X Brick 6 mm / 15/64″ D Concrete 6 mm / 15/64″ Masonry 6 mm/15/64″ D Drywall 6 mm/15/64″ *The pilot holes should be drilled to a depth of 50mm / 2″
- Step 5: Insert Anchors if Required
Insert anchor bolts if required. Secure the mounting bracket (B) by tightening the mounting screws (C).
- Step 6:Secure Mounting Bracket.
- 7 -кадам: Батареяларды салыңыз
- Carefully remove the battery cover (F) by loosening the two screws with the Torx (T10) screwdriver (E).
- Carefully replace the battery cover (F) by tightening the two battery screws with the Torx (T10) Screwdriver.
- Place the Keypad (A) onto the mounting plate (B) as shown. Secure it with the Torx (T10) screwdriver (E) from below.
- Step 8: Assemble the Keypad
Дал ушул!
You have now installed your Keypad 2 device. Please download the igloo works app to proceed with pairing.
Өзгөчөлүктөрү
Control any igloo Lock
Harness the power of no-tour PIN Codes & NFC credentials on multiple igloo locking devices.
Узактыгы үчүн иштелип чыккан
With an IK-09 Impact & IP66 Protection, the Keypad 2 is designed for heavy use.
Works for Everyone
Whether using PIN codes or key fobs, Keypad 2 eliminates reliance on mobile devices.
Үндү көзөмөлдөө
Үндү өз каалооңузга жараша тууралаңыз. 0 (үнсүз) денгээлинен 5ке (эң катуу) чейин тандаңыз.
Оңой орнотуу
A zero-wiring setup means your Keypad can be online within minutes. Can be mounted on a variety of surfaces with anchors and fasteners for wood, brick, drywall, concrete and masonry.
Flexible NFC Credential Suite
Create duration, permanent or scheduled NFC access on physical fobs or mobile devices.
Physical Keypad
Accessible, tactile buttons built for zero-error input.
Батареянын аздыгы жөнүндө эскертүү
Интуитивдик аудио жана визуалдык эскертүүлөр батарейкалардын күчү азайганда алмаштырууну сунуштайт.
Коопсуздукту жабуу
Keypad is disabled after several incorrect access attempts to ensure your property is always secure.
Audio and LED Indicators
| Аракеттер | Көрсөтмөлөр |
|---|---|
| Unlocked Successfully | Status LED flashes Blue |
| Кулпуланган | Status LED blinks Green, 4 fast ascending tones. |
| Incorrect Credential | Status LED blinks Green, single long beep. |
| Reached max. no. of digits (16) | Status LED blinks RED, 4 short beeps. |
| Security Lockout Activated | Status LED blinks RED, low-high siren for 30 /60 / 90 seconds. 2 long beeps. |
| Коопсуздукту жабуу өчүрүлдү | Status LED breathes RED when woken up, 3 fast descending tones. |
| Батареянын аздыгы жөнүндө эскертүү | Status LED blinks BLUE, 3 short beeps. |
| Hard Reset Mode | Status LED blinks RED, GREEN, BLUE, 4 slow descending tones. 2 slow beeps, 2 fast beeps. |
| Калыбына келтирүү / Ажыратуу | Status LED blinks RED, GREEN, BLUE, 4 slow descending tones. |
| Power Start Up | 2 slow beeps, 2 fast beeps. |
Документтер / Ресурстар
 |
igloo EK2 Keypad 2 [pdf] Орнотуу колдонмосу 2AYD7-EK2, EK2 Keypad 2, EK2, Keypad 2 |