speedbox Tracker Mobile App User Guide
STEP 1: Installing the SpeedBox Tracker mobile app and activating the device
A. Install the SpeedBox Tracker app on your mobile phone. Then, create a new user account or log in if you already have an account.
B. Click on „Add Device“ and scan the QR code, or enter the IMEI and PIN, which can be found on the included activation card.
App Store: https://apps.apple.com/app/speedbox-tracker/id6478385226
Google Play: https://play.google.com/store/apps/details?id=com.speedbox.GPS_tracker
2-КАДАМ: Орнотууга даярдоо
A. Turn off your e-bike before installing the SpeedBox Tracker device.
B. If possible, disconnect and remove the battery from the e-bike.
C. Following the manufacturer‘s instructions, disassemble all components of the e-bike so you have access to the motor connectors or the control unit within the e-bike frame.
STEP 3: Installing the SpeedBox Tracker device
A. Connect the adapter to the SpeedBox Tracker device.
B. Plug the adapter of the SpeedBox Tracker into the disconnected JST data connector coming from the motor.
C. Check that the connectors are properly seated and that the locking clips are securely engaged.
STEP 4: Installing the SpeedBox Tracker along with the SpeedBox Tuning device
A. SpeedBox Tuning and SpeedBox Tracker are installed independently of each other. Using a flat screwdriver, disconnect the connector of the speed sensor cable and plug the SpeedBox Tuning device into the released connectors.
B. Connect the SpeedBox Tracker to the disconnected JST data connector. Make sure that the connector locks are properly engaged and that you hear the characteristic click.
STEP 5: Completing the Installation
A. If the battery was removed, install it back.
B. Turn on the e-bike and check that everything on your e-bike is functioning correctly.
C. Электрондук велосипедди өчүрүңүз.
D. Only now reassemble the e-bike back to its original state.
E. By turning on the e-bike, the SpeedBox Tracker device will also begin to charge.
F. The SpeedBox Tracker should connect to the server within a few minutes and send information about the battery status to your mobile app. SpeedBox Tracker device comes with one-year pre-paid services. The period starts with the first successful connection to the server. As the pre-paid period nears its end, you will receive an informative email with instructions on how to renew the subscription.
STEP 6: Notice
A. If you installed the SpeedBox Tracker device in the e-bike before adding it to the app, turn off the e-bike, wait a few seconds, and then turn it back on.
B. If the data does not synchronize even after several minutes, make sure you are in an open area with signal coverage. The e-bike frame may also reduce the signal of the SpeedBox Tracker device. If there are signal issues, try finding a more suitable location for the SpeedBox Tracker device within your e-bike.
STEP 7: SpeedBox Tracker App
A. The transport mode is designed to disable route recording when transporting the e-bike, for example, by car or by air. Once activated, the transport mode will turn on during the next synchronization of the Tracker with the server. When the e-bike is turned on (powering the Tracker), the transport mode will be deactivated.
B. When the e-bike moves after the lock has been activated, you will be alerted through a notification and an SMS message to your mobile device.
C. Turning off notifications in the app will limit alerts for low battery status, expiring subscriptions, etc. However, notifications for movement of the locked Tracker will remain active.
D. Location Tracking on the Map. Clicking: The map will center on the last known position of the Tracker. Holding: The map will track the movement of the Tracker.
Ebike Electronic sro
Rybna 716/24 | 110 00 Прага 1 | Чех Республикасы | ID: 05553555 | КНС: CZ05553555
Документтер / Ресурстар
 |
speedbox Tracker Mobile App [pdf] Колдонуучунун колдонмосу 1.0, Tracker Mobile App, Mobile App |